| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Replace busylock at the Tx queuing layer with a lockless list.
Resulting in a 300% (4x) improvement on heavy TX workloads, sending
twice the number of packets per second, for half the cpu cycles.
- Allow constantly busy flows to migrate to a more suitable CPU/NIC
queue.
Normally we perform queue re-selection when flow comes out of idle,
but under extreme circumstances the flows may be constantly busy.
Add sysctl to allow periodic rehashing even if it'd risk packet
reordering.
- Optimize the NAPI skb cache, make it larger, use it in more paths.
- Attempt returning Tx skbs to the originating CPU (like we already
did for Rx skbs).
- Various data structure layout and prefetch optimizations from Eric.
- Remove ktime_get() from the recvmsg() fast path, ktime_get() is
sadly quite expensive on recent AMD machines.
- Extend threaded NAPI polling to allow the kthread busy poll for
packets.
- Make MPTCP use Rx backlog processing. This lowers the lock
pressure, improving the Rx performance.
- Support memcg accounting of MPTCP socket memory.
- Allow admin to opt sockets out of global protocol memory accounting
(using a sysctl or BPF-based policy). The global limits are a poor
fit for modern container workloads, where limits are imposed using
cgroups.
- Improve heuristics for when to kick off AF_UNIX garbage collection.
- Allow users to control TCP SACK compression, and default to 33% of
RTT.
- Add tcp_rcvbuf_low_rtt sysctl to let datacenter users avoid
unnecessarily aggressive rcvbuf growth and overshot when the
connection RTT is low.
- Preserve skb metadata space across skb_push / skb_pull operations.
- Support for IPIP encapsulation in the nftables flowtable offload.
- Support appending IP interface information to ICMP messages (RFC
5837).
- Support setting max record size in TLS (RFC 8449).
- Remove taking rtnl_lock from RTM_GETNEIGHTBL and RTM_SETNEIGHTBL.
- Use a dedicated lock (and RCU) in MPLS, instead of rtnl_lock.
- Let users configure the number of write buffers in SMC.
- Add new struct sockaddr_unsized for sockaddr of unknown length,
from Kees.
- Some conversions away from the crypto_ahash API, from Eric Biggers.
- Some preparations for slimming down struct page.
- YAML Netlink protocol spec for WireGuard.
- Add a tool on top of YAML Netlink specs/lib for reporting commonly
computed derived statistics and summarized system state.
Driver API:
- Add CAN XL support to the CAN Netlink interface.
- Add uAPI for reporting PHY Mean Square Error (MSE) diagnostics, as
defined by the OPEN Alliance's "Advanced diagnostic features for
100BASE-T1 automotive Ethernet PHYs" specification.
- Add DPLL phase-adjust-gran pin attribute (and implement it in
zl3073x).
- Refactor xfrm_input lock to reduce contention when NIC offloads
IPsec and performs RSS.
- Add info to devlink params whether the current setting is the
default or a user override. Allow resetting back to default.
- Add standard device stats for PSP crypto offload.
- Leverage DSA frame broadcast to implement simple HSR frame
duplication for a lot of switches without dedicated HSR offload.
- Add uAPI defines for 1.6Tbps link modes.
Device drivers:
- Add Motorcomm YT921x gigabit Ethernet switch support.
- Add MUCSE driver for N500/N210 1GbE NIC series.
- Convert drivers to support dedicated ops for timestamping control,
and away from the direct IOCTL handling. While at it support GET
operations for PHY timestamping.
- Add (and convert most drivers to) a dedicated ethtool callback for
reading the Rx ring count.
- Significant refactoring efforts in the STMMAC driver, which
supports Synopsys turn-key MAC IP integrated into a ton of SoCs.
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- support PPS in/out on all pins
- Intel (100G, ice, idpf):
- ice: implement standard ethtool and timestamping stats
- i40e: support setting the max number of MAC addresses per VF
- iavf: support RSS of GTP tunnels for 5G and LTE deployments
- nVidia/Mellanox (mlx5):
- reduce downtime on interface reconfiguration
- disable being an XDP redirect target by default (same as
other drivers) to avoid wasting resources if feature is
unused
- Meta (fbnic):
- add support for Linux-managed PCS on 25G, 50G, and 100G links
- Wangxun:
- support Rx descriptor merge, and Tx head writeback
- support Rx coalescing offload
- support 25G SPF and 40G QSFP modules
- Ethernet virtual:
- Google (gve):
- allow ethtool to configure rx_buf_len
- implement XDP HW RX Timestamping support for DQ descriptor
format
- Microsoft vNIC (mana):
- support HW link state events
- handle hardware recovery events when probing the device
- Ethernet NICs consumer, and embedded:
- usbnet: add support for Byte Queue Limits (BQL)
- AMD (amd-xgbe):
- add device selftests
- NXP (enetc):
- add i.MX94 support
- Broadcom integrated MACs (bcmgenet, bcmasp):
- bcmasp: add support for PHY-based Wake-on-LAN
- Broadcom switches (b53):
- support port isolation
- support BCM5389/97/98 and BCM63XX ARL formats
- Lantiq/MaxLinear switches:
- support bridge FDB entries on the CPU port
- use regmap for register access
- allow user to enable/disable learning
- support Energy Efficient Ethernet
- support configuring RMII clock delays
- add tagging driver for MaxLinear GSW1xx switches
- Synopsys (stmmac):
- support using the HW clock in free running mode
- add Eswin EIC7700 support
- add Rockchip RK3506 support
- add Altera Agilex5 support
- Cadence (macb):
- cleanup and consolidate descriptor and DMA address handling
- add EyeQ5 support
- TI:
- icssg-prueth: support AF_XDP
- Airoha access points:
- add missing Ethernet stats and link state callback
- add AN7583 support
- support out-of-order Tx completion processing
- Power over Ethernet:
- pd692x0: preserve PSE configuration across reboots
- add support for TPS23881B devices
- Ethernet PHYs:
- Open Alliance OATC14 10BASE-T1S PHY cable diagnostic support
- Support 50G SerDes and 100G interfaces in Linux-managed PHYs
- micrel:
- support for non PTP SKUs of lan8814
- enable in-band auto-negotiation on lan8814
- realtek:
- cable testing support on RTL8224
- interrupt support on RTL8221B
- motorcomm: support for PHY LEDs on YT853
- microchip: support for LAN867X Rev.D0 PHYs w/ SQI and cable diag
- mscc: support for PHY LED control
- CAN drivers:
- m_can: add support for optional reset and system wake up
- remove can_change_mtu() obsoleted by core handling
- mcp251xfd: support GPIO controller functionality
- Bluetooth:
- add initial support for PASTa
- WiFi:
- split ieee80211.h file, it's way too big
- improvements in VHT radiotap reporting, S1G, Channel Switch
Announcement handling, rate tracking in mesh networks
- improve multi-radio monitor mode support, and add a cfg80211
debugfs interface for it
- HT action frame handling on 6 GHz
- initial chanctx work towards NAN
- MU-MIMO sniffer improvements
- WiFi drivers:
- RealTek (rtw89):
- support USB devices RTL8852AU and RTL8852CU
- initial work for RTL8922DE
- improved injection support
- Intel:
- iwlwifi: new sniffer API support
- MediaTek (mt76):
- WED support for >32-bit DMA
- airoha NPU support
- regdomain improvements
- continued WiFi7/MLO work
- Qualcomm/Atheros:
- ath10k: factory test support
- ath11k: TX power insertion support
- ath12k: BSS color change support
- ath12k: statistics improvements
- brcmfmac: Acer A1 840 tablet quirk
- rtl8xxxu: 40 MHz connection fixes/support"
* tag 'net-next-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1381 commits)
net: page_pool: sanitise allocation order
net: page pool: xa init with destroy on pp init
net/mlx5e: Support XDP target xmit with dummy program
net/mlx5e: Update XDP features in switch channels
selftests/tc-testing: Test CAKE scheduler when enqueue drops packets
net/sched: sch_cake: Fix incorrect qlen reduction in cake_drop
wireguard: netlink: generate netlink code
wireguard: uapi: generate header with ynl-gen
wireguard: uapi: move flag enums
wireguard: uapi: move enum wg_cmd
wireguard: netlink: add YNL specification
selftests: drv-net: Fix tolerance calculation in devlink_rate_tc_bw.py
selftests: drv-net: Fix and clarify TC bandwidth split in devlink_rate_tc_bw.py
selftests: drv-net: Set shell=True for sysfs writes in devlink_rate_tc_bw.py
selftests: drv-net: Use Iperf3Runner in devlink_rate_tc_bw.py
selftests: drv-net: introduce Iperf3Runner for measurement use cases
selftests: drv-net: Add devlink_rate_tc_bw.py to TEST_PROGS
net: ps3_gelic_net: Use napi_alloc_skb() and napi_gro_receive()
Documentation: net: dsa: mention simple HSR offload helpers
Documentation: net: dsa: mention availability of RedBox
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Allow creaing nbcon console drivers with an unsafe write_atomic()
callback that can only be called by the final nbcon_atomic_flush_unsafe().
Otherwise, the driver would rely on the kthread.
It is going to be used as the-best-effort approach for an
experimental nbcon netconsole driver, see
https://lore.kernel.org/r/20251121-nbcon-v1-2-503d17b2b4af@debian.org
Note that a safe .write_atomic() callback is supposed to work in NMI
context. But some networking drivers are not safe even in IRQ
context:
https://lore.kernel.org/r/oc46gdpmmlly5o44obvmoatfqo5bhpgv7pabpvb6sjuqioymcg@gjsma3ghoz35
In an ideal world, all networking drivers would be fixed first and
the atomic flush would be blocked only in NMI context. But it brings
the question how reliable networking drivers are when the system is
in a bad state. They might block flushing more reliable serial
consoles which are more suitable for serious debugging anyway.
- Allow to use the last 4 bytes of the printk ring buffer.
- Prevent queuing IRQ work and block printk kthreads when consoles are
suspended. Otherwise, they create non-necessary churn or even block
the suspend.
- Release console_lock() between each record in the kthread used for
legacy consoles on RT. It might significantly speed up the boot.
- Release nbcon context between each record in the atomic flush. It
prevents stalls of the related printk kthread after it has lost the
ownership in the middle of a record
- Add support for NBCON consoles into KDB
- Add %ptsP modifier for printing struct timespec64 and use it where
possible
- Misc code clean up
* tag 'printk-for-6.19' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux: (48 commits)
printk: Use console_is_usable on console_unblank
arch: um: kmsg_dump: Use console_is_usable
drivers: serial: kgdboc: Drop checks for CON_ENABLED and CON_BOOT
lib/vsprintf: Unify FORMAT_STATE_NUM handlers
printk: Avoid irq_work for printk_deferred() on suspend
printk: Avoid scheduling irq_work on suspend
printk: Allow printk_trigger_flush() to flush all types
tracing: Switch to use %ptSp
scsi: snic: Switch to use %ptSp
scsi: fnic: Switch to use %ptSp
s390/dasd: Switch to use %ptSp
ptp: ocp: Switch to use %ptSp
pps: Switch to use %ptSp
PCI: epf-test: Switch to use %ptSp
net: dsa: sja1105: Switch to use %ptSp
mmc: mmc_test: Switch to use %ptSp
media: av7110: Switch to use %ptSp
ipmi: Switch to use %ptSp
igb: Switch to use %ptSp
e1000e: Switch to use %ptSp
...
|
|
The "a5psw" tagging protocol uses dsa_xmit_port_mask(), which means
we can offload HSR packet duplication on transmit. Enable that feature.
Cc: "Clément Léger" <clement.leger@bootlin.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251130131657.65080-14-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The "mtk" tagging protocol uses dsa_xmit_port_mask(), which means we can
offload HSR packet duplication on transmit. Enable that feature.
Cc: Daniel Golle <daniel@makrotopia.org>
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://patch.msgid.link/20251130131657.65080-13-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The "hellcreek" tagging protocol uses dsa_xmit_port_mask(), which means
we can offload HSR packet duplication on transmit. Enable that feature.
Cc: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251130131657.65080-12-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The "trailer" tagging protocol uses dsa_xmit_port_mask(), which means we
can offload HSR packet duplication on transmit. Enable that feature.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251130131657.65080-11-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Both the "gswip" and "gsw1xx" protocols use dsa_xmit_port_mask(), so
they are compatible with accelerating TX packet duplication for HSR
rings.
Enable that feature by setting the port_hsr_join() and port_hsr_leave()
operations to the simple helpers provided by DSA.
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251130131657.65080-10-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All known Realtek protocols: "rtl4a", "rtl8_4" and "rtl8_4t" use
dsa_xmit_port_mask(), so they are compatible with accelerating TX packet
duplication for HSR rings.
Enable that feature by setting the port_hsr_join() and port_hsr_leave()
operations to the simple helpers provided by DSA.
Cc: "Alvin Šipraga" <alsi@bang-olufsen.dk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Linus Walleij <linusw@kernel.org>
Link: https://patch.msgid.link/20251130131657.65080-9-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Accelerate TX packet duplication with HSR rings.
This is only possible with the NPI-based "ocelot" tagging protocol, not
with "ocelot-8021q", because the latter does not use dsa_xmit_port_mask().
This has 2 implications:
- Depending on tagging protocol, we should set (or not set) the offload
feature flags. Switching tagging protocols is done with ports down, by
design. Additional calls to dsa_port_simple_hsr_join() can be put in
the ds->ops->change_tag_protocol() path, as I had originally tried,
but this would not work: dsa_user_setup_tagger() would later clear
the feature flag that we just set. So the additional call to
dsa_port_simple_hsr_join() should sit in the ds->ops->port_enable()
call.
- When joining a HSR ring and we are currently using "ocelot-8021q",
there are cases when we should return -EOPNOTSUPP (pessimistic) and
cases when we shouldn't (optimistic). In the pessimistic case, it is a
configuration that the port won't support even with the right tagging
protocol. Distinguishing between these 2 cases matters because if we
just return -EOPNOTSUPP regardless, we lose the dp->hsr_dev pointer
and can no longer replay the offload later for the optimistic case,
from felix_port_enable().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251130131657.65080-8-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Accelerate TX packet duplication with HSR rings.
Cc: David Yang <mmyangfl@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251130131657.65080-7-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As discussed here:
https://lore.kernel.org/netdev/20240620090210.drop6jwh7e5qw556@skbuf/
the fact is that the xrs700x.c driver only supports offloading
HSR_PT_SLAVE_A and HSR_PT_SLAVE_B (which were the only port types at the
time the offload was written, _for this driver_).
Up until now, the API did not explicitly tell offloading drivers what
port has what role. So xrs700x can get confused and think that it can
support a configuration which it actually can't. There was a table in
the attached link which gave an example:
$ ip link add name hsr0 type hsr slave1 swp0 slave2 swp1 \
interlink swp2 supervision 45 version 1
HSR_PT_SLAVE_A HSR_PT_SLAVE_B HSR_PT_INTERLINK
----------------------------------------------------------------
user
space 0 1 2
requests
----------------------------------------------------------------
XRS700X
driver 1 2 -
understands
The switch would act as if the ring ports were swp1 and swp2.
Now that we have explicit hsr_get_port_type() API, let's use that to
work around the unintended semantical changes of the offloading API
brought by the introduction of interlink ports in HSR.
Fixes: 5055cccfc2d1 ("net: hsr: Provide RedBox support (HSR-SAN)")
Cc: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Link: https://patch.msgid.link/20251130131657.65080-5-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit cb675afcddbb ("net: dsa: mt7530: introduce separate MDIO driver")
exported mt7530_switch_ops for use from mt7530-mmio.c. Later in the
patch set, mt7530-mmio.c used mt7530_probe_common() to access the
mt7530_switch_ops still from mt7530.c - see commit 110c18bfed41 ("net:
dsa: mt7530: introduce driver for MT7988 built-in switch").
This proves that exporting mt7530_switch_ops was unnecessary, so
unexport it back.
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Chester A. Unal <chester.a.unal@arinc9.com>
Link: https://patch.msgid.link/20251130131657.65080-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support for STP/MST was deferred from the initial submission of the
driver.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251201094232.3155105-3-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
VLAN_CTRL should be treated as a 64-bit register. GENMASK and BIT
macros use unsigned long as the underlying type, which will result in a
build error on architectures where sizeof(long) == 4.
Replace them with unsigned long long variants.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251201094232.3155105-2-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that writing ARL entries works properly, we can actually use VID 0
as the default untagged VLAN for BCM5325 and BCM5365 as well.
So use 0 as default PVID for all chips and do not reject VLAN 0 anymore,
which we ignored since commit 45e9d59d3950 ("net: dsa: b53: do not allow
to configure VLAN 0") anyway.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251128080625.27181-8-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
BCM5325/65's ARL entry registers do not contain the VID, only the search
result register does. ARL entries have a separate VID entry register for
the index into the VLAN table.
So make ARL entry accessors use the VID entry registers instead, and
move the VLAN ID field definition to the search register definition.
Fixes: c45655386e53 ("net: dsa: b53: add support for FDB operations on 5325/5365")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251128080625.27181-7-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We currently use the mask 0xf for writing and reading b53_entry::port,
but this is only correct for unicast ARL entries. Multicast ARL entries
use a bitmask, and 0xf is not enough space for ports > 3, which includes
the CPU port.
So extend the mask accordingly to also fit port 4 (bit 4) and MII (bit
5). According to the datasheet the multicast port mask is [60:48],
making it 12 bit wide, but bits 60-55 are reserved anyway, and collide
with the priority field at [60:59], so I am not sure if this is valid.
Therefore leave it at the actual used range, [53:48].
The ARL search result register differs a bit, and there the mask is only
[52:48], so only spanning the user ports. The MII port bit is
contained in the Search Result Extension register. So create a separate
search result parse function that properly handles this.
Fixes: c45655386e53 ("net: dsa: b53: add support for FDB operations on 5325/5365")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://patch.msgid.link/20251128080625.27181-6-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On BCM5325 and BCM5365, unicast ARL entries use 8 as the value for the
CPU port, so we need to translate it to/from 5 as used for the CPU port
at most other places.
Fixes: c45655386e53 ("net: dsa: b53: add support for FDB operations on 5325/5365")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251128080625.27181-5-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
BCM5365's search result is at the same offset as BCM5325's search
result, and they (mostly) share the same format, so switch BCM5365 to
BCM5325's arl ops.
Fixes: c45655386e53 ("net: dsa: b53: add support for FDB operations on 5325/5365")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://patch.msgid.link/20251128080625.27181-4-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
BCM5325/65's Entry register uses the highest three bits for
VALID/STATIC/AGE, so shifting by 53 only will add these to
b53_arl_entry::vid.
So make sure to mask the vid value as well, to not get invalid VIDs.
Fixes: c45655386e53 ("net: dsa: b53: add support for FDB operations on 5325/5365")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://patch.msgid.link/20251128080625.27181-3-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since BCM5325 and BCM5365 only support up to 256 VLANs, the VLAN_ID_IDX
register is only 8 bit wide, not 16 bit, so use an appropriate accessor.
Fixes: c45655386e53 ("net: dsa: b53: add support for FDB operations on 5325/5365")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://patch.msgid.link/20251128080625.27181-2-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ageing time is in 5s step, ranging from 1 step to 0xffff steps, so
add appropriate attributes.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251129042137.3034032-1-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Extract MIB constants into the header file to improve code style. This
patch will not change the behavior of the function.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Link: https://patch.msgid.link/20251126084024.2843851-3-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are hard-to-find unused fields in the MIB table I didn't notice in
the example driver code, causing wrong interpretation of the MIB data.
For some 64-bit attributes, the current (wrong) implementation took the
correct lower 32 bits, but messed up the upper 32 bits, so it would work
accidentally until 32-bit overflows happen. Fix that too.
Fixes: 186623f4aa72 ("net: dsa: yt921x: Add support for Motorcomm YT921x")
Signed-off-by: David Yang <mmyangfl@gmail.com>
Link: https://patch.msgid.link/20251126084024.2843851-2-mmyangfl@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Conflicts:
net/xdp/xsk.c
0ebc27a4c67d ("xsk: avoid data corruption on cq descriptor number")
8da7bea7db69 ("xsk: add indirect call for xsk_destruct_skb")
30ed05adca4a ("xsk: use a smaller new lock for shared pool case")
https://lore.kernel.org/20251127105450.4a1665ec@canb.auug.org.au
https://lore.kernel.org/eb4eee14-7e24-4d1b-b312-e9ea738fefee@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When using the SGMII PCS as a fixed-link chip-to-chip connection, it is
easy to miss the fact that traffic passes only at 1G, since that's what
any normal such connection would use.
When using the SGMII PCS connected towards an on-board PHY or an SFP
module, it is immediately noticeable that when the link resolves to a
speed other than 1G, traffic from the MAC fails to pass: TX counters
increase, but nothing gets decoded by the other end, and no local RX
counters increase either.
Artificially lowering a fixed-link rate to speed = <100> makes us able
to see the same issue as in the case of having an SGMII PHY.
Some debugging shows that the XPCS configuration is A-OK, but that the
MAC Configuration Table entry for the port has the SPEED bits still set
to 1000Mbps, due to a special condition in the driver. Deleting that
condition, and letting the resolved link speed be programmed directly
into the MAC speed field, results in a functional link at all 3 speeds.
This piece of evidence, based on testing on both generations with SGMII
support (SJA1105S and SJA1110A) directly contradicts the statement from
the blamed commit that "the MAC is fixed at 1 Gbps and we need to
configure the PCS only (if even that)". Worse, that statement is not
backed by any documentation, and no one from NXP knows what it might
refer to.
I am unable to recall sufficient context regarding my testing from March
2020 to understand what led me to draw such a braindead and factually
incorrect conclusion. Yet, there is nothing of value regarding forcing
the MAC speed, either for SGMII or 2500Base-X (introduced at a later
stage), so remove all such logic.
Fixes: ffe10e679cec ("net: dsa: sja1105: Add support for the SGMII port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251122111324.136761-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The IRQ numbers created through irq_create_mapping() are only assigned
to ptpmsg_irq[n].num at the end of the IRQ setup. So if an error occurs
between their creation and their assignment (for instance during the
request_threaded_irq() step), we enter the error path and fail to
release the newly created virtual IRQs because they aren't yet assigned
to ptpmsg_irq[n].num.
Move the mapping creation to ksz_ptp_msg_irq_setup() to ensure symetry
with what's released by ksz_ptp_msg_irq_free().
In the error path, move the irq_dispose_mapping to the out_ptp_msg label
so it will be called only on created IRQs.
Cc: stable@vger.kernel.org
Fixes: cc13ab18b201 ("net: dsa: microchip: ptp: enable interrupt for timestamping")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-5-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If a port interrupt setup fails after at least one port has already been
successfully initialized, the gotos miss some resource releasing:
- the already initialized PTP IRQs aren't released
- the already initialized port IRQs aren't released if the failure
occurs in ksz_pirq_setup().
Merge 'out_girq' and 'out_ptpirq' into a single 'port_release' label.
Behind this label, use the reverse loop to release all IRQ resources
for all initialized ports.
Jump in the middle of the reverse loop if an error occurs in
ksz_ptp_irq_setup() to only release the port IRQ of the current
iteration.
Cc: stable@vger.kernel.org
Fixes: c9cd961c0d43 ("net: dsa: microchip: lan937x: add interrupt support for port phy link")
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-4-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If something goes wrong at setup, ksz_irq_free() can be called on
uninitialized ksz_irq (for example when ksz_ptp_irq_setup() fails). It
leads to freeing uninitialized IRQ numbers and/or domains.
Use dsa_switch_for_each_user_port_continue_reverse() in the error path
to iterate only over the fully initialized ports.
Cc: stable@vger.kernel.org
Fixes: cc13ab18b201 ("net: dsa: microchip: ptp: enable interrupt for timestamping")
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-3-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
irq_find_mapping() returns a positive IRQ number or 0 if no IRQ is found
but it never returns a negative value. However, during the PTP IRQ setup,
we verify that its returned value isn't negative.
Fix the irq_find_mapping() check to enter the error path when 0 is
returned. Return -EINVAL in such case.
Cc: stable@vger.kernel.org
Fixes: cc13ab18b201 ("net: dsa: microchip: ptp: enable interrupt for timestamping")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-2-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
irq_find_mapping() returns a positive IRQ number or 0 if no IRQ is found
but it never returns a negative value. However, on each
irq_find_mapping() call, we verify that the returned value isn't
negative.
Fix the irq_find_mapping() checks to enter error paths when 0 is
returned. Return -EINVAL in such cases.
CC: stable@vger.kernel.org
Fixes: c9cd961c0d43 ("net: dsa: microchip: lan937x: add interrupt support for port phy link")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Bastien Curutchet (Schneider Electric) <bastien.curutchet@bootlin.com>
Link: https://patch.msgid.link/20251120-ksz-fix-v6-1-891f80ae7f8f@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Cross-merge networking fixes after downstream PR (net-6.18-rc7).
No conflicts, adjacent changes:
tools/testing/selftests/net/af_unix/Makefile
e1bb28bf13f4 ("selftest: af_unix: Add test for SO_PEEK_OFF.")
45a1cd8346ca ("selftests: af_unix: Add tests for ECONNRESET and EOF semantics")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Correct RGMII delay application logic in lan937x_set_tune_adj().
The function was missing `data16 &= ~PORT_TUNE_ADJ` before setting the
new delay value. This caused the new value to be bitwise-OR'd with the
existing PORT_TUNE_ADJ field instead of replacing it.
For example, when setting the RGMII 2 TX delay on port 4, the
intended TUNE_ADJUST value of 0 (RGMII_2_TX_DELAY_2NS) was
incorrectly OR'd with the default 0x1B (from register value 0xDA3),
leaving the delay at the wrong setting.
This patch adds the missing mask to clear the field, ensuring the
correct delay value is written. Physical measurements on the RGMII TX
lines confirm the fix, showing the delay changing from ~1ns (before
change) to ~2ns.
While testing on i.MX 8MP showed this was within the platform's timing
tolerance, it did not match the intended hardware-characterized value.
Fixes: b19ac41faa3f ("net: dsa: microchip: apply rgmii tx and rx delay in phylink mac config")
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20251114090951.4057261-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Use %ptSp instead of open coded variants to print content of
struct timespec64 in human readable format.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20251113150217.3030010-15-andriy.shevchenko@linux.intel.com
Signed-off-by: Petr Mladek <pmladek@suse.com>
|
|
The driver declares an OF match table named ks8895_spi_of_match, even
though it describes compatible strings for the KS8995 and related Micrel
switches. This is a leftover typo, the correct name should match the
chip family handled by this driver ks8995, and also match the variable
used in spi_driver.of_match_table.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patch.msgid.link/20251117095356.2099772-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The LED setup routine registered both led_sync_good
and led_is_gm devices without checking the return
values of led_classdev_register(). If either registration
failed, the function continued silently, leaving the
driver in a partially-initialized state and leaking
a registered LED classdev.
Add proper error handling
Fixes: 7d9ee2e8ff15 ("net: dsa: hellcreek: Add PTP status LEDs")
Signed-off-by: Pavel Zhigulin <Pavel.Zhigulin@kaspersky.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://patch.msgid.link/20251113135745.92375-1-Pavel.Zhigulin@kaspersky.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use new helper fixed_phy_register_100fd to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/922f1b45-1748-4dd2-87eb-9d018df44731@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ARL registers of BCM63XX embedded switches are somewhat unique. The
normal ARL table access registers have the same format as BCM5389, but
the ARL search registers differ:
* SRCH_CTL is at the same offset of BCM5389, but 16 bits wide. It does
not have more fields, just needs to be accessed by a 16 bit read.
* SRCH_RSLT_MACVID and SRCH_RSLT are aligned to 32 bit, and have shifted
offsets.
* SRCH_RSLT has a different format than the normal ARL data entry
register.
* There is only one set of ENTRY_N registers, implying a 1 bin layout.
So add appropriate ops for bcm63xx and let it use it.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251107080749.26936-9-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
BCM5389, BCM5397 and BCM5398 use a different ARL entry format with just
a 16 bit fwdentry register, as well as different search control and data
offsets.
So add appropriate ops for them and switch those chips to use them.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251107080749.26936-8-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Now that the differences in ARL entry formats are neatly contained into
functions per chip family, wrap them into an ops struct and add wrapper
functions to access them.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251107080749.26936-7-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Split reading search entries into a function for each format.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251107080749.26936-6-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In order to more easily support more formats, move accessing
ARL_SRCH_CTL into helper functions to contain the differences.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251107080749.26936-5-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move writing ARL entries into individual functions for each format.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251107080749.26936-4-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Instead of duplicating the whole code iterating over all bins for
BCM5325, factor out reading and parsing the entry into its own
functions, and name it the modern one after the first chip with that ARL
format, (BCM53)95.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251107080749.26936-3-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Align the b53_arl_read{,25}() functions by consistently using the
parsed arl entry instead of parsing the raw registers again.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251107080749.26936-2-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add driver for the MaxLinear GSW1xx family of Ethernet switch ICs which
are based on the same IP as the Lantiq/Intel GSWIP found in the Lantiq VR9
and Intel GRX MIPS router SoCs. The main difference is that instead of
using memory-mapped I/O to communicate with the host CPU these ICs are
connected via MDIO (or SPI, which isn't supported by this driver).
Implement the regmap API to access the switch registers over MDIO to allow
reusing lantiq_gswip_common for all core functionality.
The GSW1xx also comes with a SerDes port capable of 1000Base-X, SGMII and
2500Base-X, which can either be used to connect an external PHY or SFP
cage, or as the CPU port. Support for the SerDes interface is implemented
in this driver using the phylink_pcs interface.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://patch.msgid.link/b567ec1b4beb08fd37abf18b280c56d5d8253c26.1762170107.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the MII clk vs. data delay is configured based on the PHY
interface mode.
In addition to that add support for setting up MII delays using the
standard Device Tree properties 'tx-internal-delay-ps' and
'rx-internal-delay-ps', using the values determined by the PHY interface
mode as default to maintain backward compatibility with legacy device
trees.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/37203e831cff87dc46e5ef9e8cbd68fb8689773d.1762170107.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Read boolean Device Tree property "maxlinear,rmii-refclk-out" and switch
the RMII reference clock to be a clock output rather than an input if it
is set.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://patch.msgid.link/947d14970f74f760e4a60c777aabee64e7e4f356.1762170107.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When adding FDB entries to the MAC bridge table on GSWIP 2.2 or later it
is needed to set an (undocumented) bit to mark the entry as valid. If this
bit isn't set for entries in the MAC bridge table, then those entries won't
be considered as valid MAC addresses.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/e02fe0d946c98920bc55b5f389a8f56382aae7df.1762170107.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On standalone switch ICs the link parameters of the CPU port need to
be setup just like user ports. The destinction in the driver to not
carry out link parameter setup for the CPU port does make sense for
in-SoC switches on which the CPU port is internally connected to the
SoC's Ethernet MAC.
Set link parameters also for the CPU port unless it is an internal
interface. Note that the internal TP PHYs anyway cannot be used as
CPU ports, hence it doesn't matter that they are now also covered by
that condition.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/07c6b8d3a12296123be5e5938b454fc620f819e6.1762170107.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
