| Age | Commit message (Collapse) | Author |
|---|
|
Merge in late fixes in preparation for the net-next PR.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for Signal Quality Index (SQI) reporting in the
Microchip T1S PHY driver for LAN867x Rev.D0 (OATC14-compliant) PHYs.
This patch registers the following callbacks in the microchip_t1s driver
structure:
- .get_sqi - returns the current SQI value
- .get_sqi_max - returns the maximum SQI value
This enables ethtool to report the SQI value for LAN867x Rev.D0 PHYs.
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251201032346.6699-3-parthiban.veerasooran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for reading Signal Quality Indicator (SQI) and enhanced SQI+
from OATC14 10Base-T1S PHYs.
- Introduce MDIO register definitions for DCQ_SQI and DCQ_SQIPLUS.
- Add `genphy_c45_oatc14_get_sqi_max()` to return the maximum supported
SQI/SQI+ level.
- Add `genphy_c45_oatc14_get_sqi()` to return the current SQI or SQI+
value.
- Update `include/linux/phy.h` to expose the new APIs.
SQI+ capability is read from the Advanced Diagnostic Features Capability
register (ADFCAP). If SQI+ is supported, the driver calculates the value
from the MSBs of the DCQ_SQIPLUS register; otherwise, it falls back to
basic SQI (0-7 levels). This enables ethtool to report the SQI value for
OATC14 10Base-T1S PHYs.
Open Alliance TC14 10BASE-T1S Advanced Diagnostic PHY Features
Specification ref:
https://opensig.org/wp-content/uploads/2025/06/OPEN_Alliance_10BASE-T1S_Advanced_PHY_features_for-automotive_Ethernet_V2.1b.pdf
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251201032346.6699-2-parthiban.veerasooran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, if NVMEM provider is probed later than Aquantia, loading the
firmware will fail with -EINVAL.
To fix this, simply check for -EPROBE_DEFER when NVMEM is attempted and
return it.
Fixes: e93984ebc1c8 ("net: phy: aquantia: add firmware load support")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20251127114514.460924-1-robimarko@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Conflicts:
net/xdp/xsk.c
0ebc27a4c67d ("xsk: avoid data corruption on cq descriptor number")
8da7bea7db69 ("xsk: add indirect call for xsk_destruct_skb")
30ed05adca4a ("xsk: use a smaller new lock for shared pool case")
https://lore.kernel.org/20251127105450.4a1665ec@canb.auug.org.au
https://lore.kernel.org/eb4eee14-7e24-4d1b-b312-e9ea738fefee@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The 2.5G and 5G values are not consistent between the PCS CTRL1 and PMA
CTRL1 values. In order to avoid confusion between the two I am updating the
values to include "PMA" in the name similar to values used in similar
places.
To avoid breaking UAPI I have retained the original macros and just defined
them as the new PMA based defines.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://patch.msgid.link/176374319569.959489.6610469879021800710.stgit@ahduyck-xeon-server.home.arpa
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Implement the inband_caps() and config_inband() PHY driver methods, to
allow working with PCS devices that do not support or want in-band to be
used.
There is a complication due to existing logic from commit c76acfb7e19d
("net: phy: dp83867: retrigger SGMII AN when link change") which might
re-enable what dp83867_config_inband() has disabled. So we need to
modify dp83867_link_change_notify() to use phy_modify_changed() when
temporarily disabling in-band autoneg. If the return code is 0, it means
the original in-band was disabled and we need to keep it disabled.
If the return code is 1, the original was enabled and we need to
re-enable it. If negative, there was an error, which was silent before,
and remains silent now.
dp83867_config_inband() and dp83867_link_change_notify() are serialized
by the phydev->lock.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251122110427.133035-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver stores HW timestamping configuration and can technically
report it. Add callback to do it.
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251124181151.277256-7-vadim.fedorenko@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver stores HW configuration and can technically report it.
Add callback to do it.
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251124181151.277256-6-vadim.fedorenko@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver stores configuration of TX timestamping and can technically
report it. Patch RX timestamp configuration storage to be more precise
on reporting and add callback to actually report it.
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251124181151.277256-5-vadim.fedorenko@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver stores configuration information and can technically report
it. Implement hwtstamp_get callback to report the configuration.
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251124181151.277256-4-vadim.fedorenko@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
PHY devices had lack of hwtstamp_get callback even though most of them
are tracking configuration info. Introduce new call back to
mii_timestamper.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251124181151.277256-3-vadim.fedorenko@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
PHY devices has hwtstamp callback which actually performs set operation.
Rename it to better reflect the action.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251124181151.277256-2-vadim.fedorenko@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add PHY driver support for Maxlinear MxL86252 and MxL86282 switches.
The PHYs built-into those switches are just like any other GPY 2.5G PHYs
with the exception of the temperature sensor data being encoded in a
different way.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/a6cd7fe461b011cec2b59dffaf34e9c8b0819059.1763818120.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
MxL86211C is a smaller and more efficient version of the GPY211C.
Add the PHY ID and phy_driver instance to the mxl-gpy driver.
Signed-off-by: Chad Monroe <chad@monroe.io>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/cabf3559d6511bed6b8a925f540e3162efc20f6b.1763818120.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix all warnings reported by scripts/kernel-doc in
mdio_device.c and mdio_bus.c
Signed-off-by: Buday Csaba <buday.csaba@prolan.hu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/7ef7b80669da2b899d38afdb6c45e122229c3d8c.1763968667.git.buday.csaba@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
gpy_update_interface() returns early in case the PHY is internal or
connected via USXGMII. In this case the gigabit master/slave property
as well as MDI/MDI-X status also won't be read which seems wrong.
Always read those properties by moving the logic to retrieve them to
gpy_read_status().
Fixes: fd8825cd8c6fc ("net: phy: mxl-gpy: Add PHY Auto/MDI/MDI-X set driver for GPY211 chips")
Fixes: 311abcdddc00a ("net: phy: add support to get Master-Slave configuration")
Suggested-by: "Russell King (Oracle)" <linux@armlinux.org.uk>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/71fccf3f56742116eb18cc070d2a9810479ea7f9.1763650701.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As the interface mode doesn't need to be updated on PHYs connected with
USXGMII and integrated PHYs, gpy_update_interface() should just return 0
in these cases rather than -EINVAL which has wrongly been introduced by
commit 7a495dde27ebc ("net: phy: mxl-gpy: Change gpy_update_interface()
function return type"), as this breaks support for those PHYs.
Fixes: 7a495dde27ebc ("net: phy: mxl-gpy: Change gpy_update_interface() function return type")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/f744f721a1fcc5e2e936428c62ff2c7d94d2a293.1763648168.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for 1600Gbps link modes based on 200Gbps per lane [1].
This includes the adopted IEEE 802.3dj copper and optical PMDs that use
200G/lane signaling [2].
Add the following PMD types:
- KR8 (backplane)
- CR8 (copper cable)
- DR8 (SMF 500m)
- DR8-2 (SMF 2km)
These modes are defined in the 802.3dj specifications.
References:
[1] https://www.ieee802.org/3/dj/public/23_03/opsasnick_3dj_01a_2303.pdf
[2] https://www.ieee802.org/3/dj/projdoc/objectives_P802d3dj_240314.pdf
Signed-off-by: Yael Chemla <ychemla@nvidia.com>
Reviewed-by: Shahar Shitrit <shshitrit@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/1763585297-1243980-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All these members are populated by the phylib state machine once the
PHY has been started, based on the fixed autoneg results.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/bc666a53-5469-4e9c-85a1-dd285aadfe4f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Original change remove the link initialization from the passed struct
fixed_phy_status, but @status is also passed to __fixed_phy_add(),
where it is saved. Make sure that copy also has link set to 1.
Fixes: 9f07af1d2742 ("net: phy: fixed_phy: initialize the link status as up")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/dab6c10e-725e-4648-9662-39cc821723d0@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The additional use case for that variable is gone,
the expression is simple enough to pass it inline now.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20251119124737.280939-3-ada@thorsis.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Value CRSM_SFT_PD written to Software Power-Down Control Register
(CRSM_SFT_PD_CNTRL) is 0x01 and therefor different to value
CRSM_SFT_PD_RDY (0x02) read from System Status Register (CRSM_STAT) for
confirmation powerdown has been reached.
The condition could have only worked when disabling powerdown
(both 0x00), but never when enabling it (0x01 != 0x02).
Result is a timeout, like so:
$ ifdown eth0
macb f802c000.ethernet eth0: Link is Down
ADIN1100 f802c000.ethernet-ffffffff:01: adin_set_powerdown_mode failed: -110
ADIN1100 f802c000.ethernet-ffffffff:01: adin_set_powerdown_mode failed: -110
Fixes: 7eaf9132996a ("net: phy: adin1100: Add initial support for ADIN1100 industrial PHY")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20251119124737.280939-2-ada@thorsis.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Change fwnode_property_read_u32() in mdio_device_register_reset()
to device_property_read_u32(), which is more appropriate here.
Make mdio_device_unregister_reset() truly reverse
mdio_device_register_reset() by setting the internal fields to
their default values.
Signed-off-by: Buday Csaba <buday.csaba@prolan.hu>
Link: https://patch.msgid.link/641df1488517ae71ba10158ec1e38424211d8651.1763473655.git.buday.csaba@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Unify the handling of the per device reset properties for
`mdio_device`.
Merge mdio_device_register_gpiod() and mdio_device_register_reset()
into mdio_device_register_reset(), that handles both
reset-controllers and reset-gpios.
Move reading of the reset firmware properties (reset-assert-us,
reset-deassert-us) from fwnode_mdio.c to mdio_device_register_reset(),
so all reset related initialization code is kept in one place.
Introduce mdio_device_unregister_reset() to release the associated
resources.
These changes make tracking the reset properties easier.
Added kernel-doc for mdio_device_register/unregister_reset().
Signed-off-by: Buday Csaba <buday.csaba@prolan.hu>
Link: https://patch.msgid.link/17c216efd7a47be17db104378b6aacfc8741d8b9.1763473655.git.buday.csaba@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The functions mdiobus_register_gpiod() and mdiobus_register_reset()
handle the mdio device reset initialization, which belong to
mdio_device.c.
Move them from mdio_bus.c to mdio_device.c, and rename them to match
the corresponding source file: mdio_device_register_gpio() and
mdio_device_register_reset().
Remove 'static' qualifiers and declare them in
drivers/net/phy/mdio-private.h (new header file).
Signed-off-by: Buday Csaba <buday.csaba@prolan.hu>
Link: https://patch.msgid.link/5f684838ee897130f21b21beb07695eea4af8988.1763473655.git.buday.csaba@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.18-rc7).
No conflicts, adjacent changes:
tools/testing/selftests/net/af_unix/Makefile
e1bb28bf13f4 ("selftest: af_unix: Add test for SO_PEEK_OFF.")
45a1cd8346ca ("selftests: af_unix: Add tests for ECONNRESET and EOF semantics")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
To simplify the rtl8211f_config_init() control flow and get rid of
"early" returns for PHYs where the PHYCR2 register is absent, move the
entire logic sub-block that deals with disabling PHY-mode EEE to a
separate function. There, it is much more obvious what the early
"return 0" skips, and it becomes more difficult to accidentally skip
unintended stuff.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251117234033.345679-7-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Previous changes have replaced the machine-level priv->phycr2 with a
high-level priv->disable_clk_out. This created a discrepancy with
priv->phycr1 which is resolved here, for uniformity.
One advantage of this new implementation is that we don't read
priv->phycr1 in rtl821x_probe() if we're never going to modify it.
We never test the positive return code from phy_modify_mmd_changed(), so
we could just as well use phy_modify_mmd().
I took the ALDPS feature description from commit d90db36a9e74 ("net:
phy: realtek: add dt property to enable ALDPS mode") and transformed it
into a function comment - the feature is sufficiently non-obvious to
deserve that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251117234033.345679-6-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add CLKOUT disable support for RTL8211F(D)(I)-VD-CG. Like with other PHY
variants, this feature might be requested by customers when the clock
output is not used, in order to reduce electromagnetic interference (EMI).
In the common driver, the CLKOUT configuration is done through PHYCR2.
The RTL_8211FVD_PHYID is singled out as not having that register, and
execution in rtl8211f_config_init() returns early after commit
2c67301584f2 ("net: phy: realtek: Avoid PHYCR2 access if PHYCR2 not
present").
But actually CLKOUT is configured through a different register for this
PHY. Instead of pretending this is PHYCR2 (which it is not), just add
some code for modifying this register inside the rtl8211f_disable_clk_out()
function, and move that outside the code portion that runs only if
PHYCR2 exists.
In practice this reorders the PHYCR2 writes to disable PHY-mode EEE and
to disable the CLKOUT for the normal RTL8211F variants, but this should
be perfectly fine.
It was not noted that RTL8211F(D)(I)-VD-CG would need a genphy_soft_reset()
call after disabling the CLKOUT. Despite that, we do it out of caution
and for symmetry with the other RTL8211F models.
Co-developed-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251117234033.345679-5-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This variable is assigned in rtl821x_probe() and used in
rtl8211f_config_init(), which is more complex than it needs to be.
Simply testing the same condition from rtl821x_probe() in
rtl8211f_config_init() yields the same result (the PHY driver ID is a
runtime invariant), but with one temporary variable less.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251117234033.345679-4-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The RTL8211F(D)(I)-VD-CG PHY also has support for disabling the CLKOUT,
and we'd like to introduce the "realtek,clkout-disable" property for
that.
But it isn't done through the PHYCR2 register, and it becomes awkward to
have the driver pretend that it is. So just replace the machine-level
"u16 phycr2" variable with a logical "bool disable_clk_out", which
scales better to the other PHY as well.
The change is a complete functional equivalent. Before, if the device
tree property was absent, priv->phycr2 would contain the RTL8211F_CLKOUT_EN
bit as read from hardware. Now, we don't save priv->phycr2, but we just
don't call phy_modify_paged() on it. Also, we can simply call
phy_modify_paged() with the "set" argument to 0.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251117234033.345679-3-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The control flow in rtl8211f_config_init() has some pitfalls which were
probably unintended. Specifically it has an early return:
switch (phydev->interface) {
...
default: /* the rest of the modes imply leaving delay as is. */
return 0;
}
which exits the entire config_init() function. This means it also skips
doing things such as disabling CLKOUT or disabling PHY-mode EEE.
For the RTL8211FS, which uses PHY_INTERFACE_MODE_SGMII, this might be a
problem. However, I don't know that it is, so there is no Fixes: tag.
The issue was observed through code inspection.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251117234033.345679-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pause, Asym_Pause and Autoneg bits are not set when pl->supported is
initialized, so these link modes will not work for the fixed-link. This
leads to a TCP performance degradation issue observed on the i.MX943
platform.
The switch CPU port of i.MX943 is connected to an ENETC MAC, this link
is a fixed link and the link speed is 2.5Gbps. And one of the switch
user ports is the RGMII interface, and its link speed is 1Gbps. If the
flow-control of the fixed link is not enabled, we can easily observe
the iperf performance of TCP packets is very low. Because the inbound
rate on the CPU port is greater than the outbound rate on the user port,
the switch is prone to congestion, leading to the loss of some TCP
packets and requiring multiple retransmissions.
Solving this problem should be as simple as setting the Asym_Pause and
Pause bits. The reason why the Autoneg bit needs to be set, Russell
has gave a very good explanation in the thread [1], see below.
"As the advertising and lp_advertising bitmasks have to be non-empty,
and the swphy reports aneg capable, aneg complete, and AN enabled, then
for consistency with that state, Autoneg should be set. This is how it
was prior to the blamed commit."
Fixes: de7d3f87be3c ("net: phylink: Use phy_caps_lookup for fixed-link configuration")
Link: https://lore.kernel.org/aRjqLN8eQDIQfBjS@shell.armlinux.org.uk # [1]
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20251117102943.1862680-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The lan8814 supports two interfaces towards the host (QSGMII and QUSGMII).
Currently the lan8814 disables the auto-negotiation towards the host
side. So, extend this to allow to configure to use in-band
auto-negotiation.
I have tested this only with the QSGMII interface.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20251114084224.3268928-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The "phy-mode" property of devicetree indicates whether the PCB has
delay now, which means the mac needs to modify the PHY mode based
on whether there is an internal delay in the mac.
This modification is similar for many ethernet drivers. To simplify
code, define the helper phy_fix_phy_mode_for_mac_delays(speed, mac_txid,
mac_rxid) to fix PHY mode based on whether mac adds internal delay.
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251114003805.494387-3-inochiama@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
fixed_phy_register
This code was added with 34b31da486a5 ("phy: fixed_phy: Set supported
speed in phydev") 10 yrs ago. The commit message of this change
mentions a use case involving callback adjust_link of struct
dsa_switch_driver. This struct doesn't exist any longer, and in general
usage of the legacy fixed PHY has been removed from DSA with the switch
to phylink.
Note: Supported and advertised modes are now set by phy_probe() when
the fixed PHY is attached to the netdev and bound to the genphy driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/3abaa3c5-fbb9-4052-9346-6cb096a25878@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
devm_phy_package_join() may fail and return a negative error code.
Update vsc85xx_probe_common() to properly handle this failure by
checking the return value and propagating the error to the caller.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251112135715.1017117-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for the PHY LED controller in the MSCC VSC85xx driver. The
implementation provides LED brightness and hardware control through the
LED subsystem and integrates with the standard 'netdev' trigger.
Introduce new register definitions for the LED behavior register
(MSCC_PHY_LED_BEHAVIOR = 30) and the LED combine disable bits, which
control whether LEDs indicate link-only or combined link and activity
status. Implement a helper, vsc8541_led_combine_disable_set(), to update
these bits safely using phy_modify().
Add support for LED brightness control and hardware mode configuration.
The new callbacks implement the standard LED class operations, allowing
user control through sysfs. The brightness control maps to PHY LED force
on/off modes. The hardware control get and set functions translate
between the PHY-specific LED mode encodings and the LED subsystem
TRIGGER_NETDEV_* rules.
The combine feature is managed automatically based on the selected
rules. When both RX and TX activity are disabled, the combine feature is
turned off, causing LEDs to indicate link-only status. When either RX or
TX activity is enabled, the combine feature remains active and LEDs
indicate combined link and activity.
Register the LED callbacks for all VSC85xx PHY variants so that the LED
subsystem can manage their indicators consistently. Existing device tree
LED configuration and default behavior are preserved.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251112135715.1017117-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Unify the probe implementations of the VSC85xx PHY family into a single
vsc85xx_probe_common() helper. The existing probe functions for the
vsc85xx, vsc8514, vsc8574, and vsc8584 variants contained almost
identical initialization logic, differing only in configuration
parameters such as the number of LEDs, supported LED modes, hardware
statistics, and PTP support.
Introduce a vsc85xx_probe_config structure to describe the per-variant
parameters, and move all common setup code into the shared helper. Each
variant's probe function now defines a constant configuration instance
and calls vsc85xx_probe_common().
Also mark the default LED mode array parameter as const to match its
usage.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251112135715.1017117-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The vsc85xx_led_cntl_set() function currently performs a manual
read-modify-write sequence protected by the PHY lock to update the
LED mode register (MSCC_PHY_LED_MODE_SEL).
Replace this sequence with a call to phy_modify(), which already
handles read-modify-write operations with proper locking inside
the PHY core.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20251112135715.1017117-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.18-rc6).
No conflicts, adjacent changes in:
drivers/net/phy/micrel.c
96a9178a29a6 ("net: phy: micrel: lan8814 fix reset of the QSGMII interface")
61b7ade9ba8c ("net: phy: micrel: Add support for non PTP SKUs for lan8814")
and a trivial one in tools/testing/selftests/drivers/net/Makefile.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All callers initialize the link status as up. This change is in line
with how of_phy_register_fixed_link() behaves.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/45f644e8-2292-4787-a27a-f69084c93218@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Fix a possible leak in mdiobus_register_device() when both a
reset-gpio and a reset-controller are present.
Clean up the already claimed reset-gpio, when the registration of
the reset-controller fails, so when an error code is returned, the
device retains its state before the registration attempt.
Link: https://lore.kernel.org/all/20251106144603.39053c81@kernel.org/
Fixes: 71dd6c0dff51 ("net: phy: add support for reset-controller")
Signed-off-by: Buday Csaba <buday.csaba@prolan.hu>
Link: https://patch.msgid.link/4b419377f8dd7d2f63f919d0f74a336c734f8fff.1762584481.git.buday.csaba@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The lan8814 is a quad-phy and it is using QSGMII towards the MAC.
The problem is that everytime when one of the ports is configured then
the PCS is reseted for all the PHYs. Meaning that the other ports can
loose traffic until the link is establish again.
To fix this, do the reset one time for the entire PHY package.
Fixes: ece19502834d ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Divya Koppera <Divya.Koppera@microchip.com >
Link: https://patch.msgid.link/20251106090637.2030625-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All three members are effectively of type bool, so make this explicit
and shrink size of struct fixed_phy_status.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/9eca3d7e-fa64-4724-8fdc-f2c1a8f2ae8f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Enable Open Alliance TC14 (OATC14) 10Base-T1S cable diagnostic feature
for Microchip LAN867x Rev.D0 PHY by implementing `cable_test_start` and
`cable_test_get_status` using the generic C45 functions. This allows the
`ethtool` utility to perform cable diagnostic tests directly on the PHY,
improving network troubleshooting and maintenance.
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Link: https://patch.msgid.link/20251105051213.50443-3-parthiban.veerasooran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for Open Alliance TC14 (OATC14) 10BASE-T1S PHYs cable
diagnostic feature.
This patch implements:
- genphy_c45_oatc14_cable_test_start() to initiate a cable test
- genphy_c45_oatc14_cable_test_get_status() to retrieve test results
- Helper function to map PHY cable test status to ethtool result codes
- Function declarations and exports for use by PHY drivers
This enables ethtool to report ok, open, short, and undetectable cable
conditions on OATC14 10Base-T1S PHYs.
Open Alliance TC14 10BASE-T1S Advanced Diagnostic PHY Features
Specification ref:
https://opensig.org/wp-content/uploads/2025/06/OPEN_Alliance_10BASE-T1S_Advanced_PHY_features_for-automotive_Ethernet_V2.1b.pdf
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Link: https://patch.msgid.link/20251105051213.50443-2-parthiban.veerasooran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Wait until a PHY becomes ready in the probe callback by
using read_poll_timeout function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Reviewed-by: Gary Guo <gary@garyguo.net>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Link: https://patch.msgid.link/20251105133126.3221948-1-fujita.tomonori@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.18-rc5).
Conflicts:
drivers/net/wireless/ath/ath12k/mac.c
9222582ec524 ("Revert "wifi: ath12k: Fix missing station power save configuration"")
6917e268c433 ("wifi: ath12k: Defer vdev bring-up until CSA finalize to avoid stale beacon")
https://lore.kernel.org/11cece9f7e36c12efd732baa5718239b1bf8c950.camel@sipsolutions.net
Adjacent changes:
drivers/net/ethernet/intel/Kconfig
b1d16f7c0063 ("libie: depend on DEBUG_FS when building LIBIE_FWLOG")
93f53db9f9dc ("ice: switch to Page Pool")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
