summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath/ath12k/core.c
AgeCommit message (Collapse)Author
2025-11-06wifi: ath12k: Fix timeout error during beacon stats retrievalManish Dharanenthiran
Currently, for beacon_stats, ath12k_mac_get_fw_stats() is called for each started BSS on the specified hardware. ath12k_mac_get_fw_stats() will wait for the fw_stats_done completion after fetching the requested data from firmware. For the beacon_stats, fw_stats_done completion will be set only when stats are received for all BSSes. However, for other stats like vdev_stats or pdev_stats, there is one request to the firmware for all enabled BSSes. Since beacon_stats is fetched individually for all BSSes enabled in that pdev, waiting for the completion event results in a timeout error when multiple BSSes are enabled. Avoid this by completing the fw_stats_done immediately after updating the requested BSS's beacon stats in the list. Subsequently, this list will be used to display the beacon stats for all enabled BSSes in the requested pdev. Additionally, remove 'num_bcn_recvd' from the ath12k_fw_stats struct as it is no longer needed. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1 Fixes: 9fe4669ae919 ("wifi: ath12k: Request beacon stats from firmware") Signed-off-by: Manish Dharanenthiran <manish.dharanenthiran@oss.qualcomm.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com> Link: https://patch.msgid.link/20251031-beacon_stats-v1-2-f52fce7b03ac@qti.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-10-30wifi: ath12k: fix error handling in creating hardware groupBaochen Qiang
In ath12k_core_init() when ath12k_core_hw_group_create() fails, ath12k_core_hw_group_destroy() is called where for each device below path would get executed ath12k_core_soc_destroy() ath12k_qmi_deinit_service() qmi_handle_release() This results in kernel crash in case one of the device fails at qmi_handle_init() when creating hardware group: ath12k_pci 0000:10:00.0: failed to initialize qmi handle ath12k_pci 0000:10:00.0: failed to initialize qmi :-517 ath12k_pci 0000:10:00.0: failed to create soc core: -517 ath12k_pci 0000:10:00.0: unable to create hw group BUG: unable to handle page fault for address: ffffffffffffffb7 RIP: 0010:qmi_handle_release Call Trace: <TASK> ath12k_qmi_deinit_service ath12k_core_hw_group_destroy ath12k_core_init ath12k_pci_probe The detailed reason is, when qmi_handle_init() fails for a device ab->qmi.handle is not correctly initialized. Then ath12k_core_hw_group_create() returns failure, since error handing is done for all device, eventually qmi_handle_release() is called for the issue device and finally kernel crashes due to the uninitialized ab->qmi.handle. Fix this by moving error handling to ath12k_core_hw_group_create(), this way the issue device can be skipped. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Fixes: 6f245ea0ec6c ("wifi: ath12k: introduce device group abstraction") Link: https://lore.kernel.org/ath12k/fabc97122016d1a66a53ddedd965d134@posteo.net Reported-by: a-development <a-development@posteo.de> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220518 Tested-by: a-development <a-development@posteo.de> Signed-off-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20251030-fix-hw-group-create-err-handling-v1-1-0659e4d15fb9@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-07-21wifi: ath12k: Prefer {} to {0} in initializersJeff Johnson
Prefer {} to {0} in initializers since {} works even when the first member is not a scalar. Generated using: sed -i 's/{[[:space:]]*0[[:space:]]*}/{}/g' drivers/net/wireless/ath/ath12k/* Compile tested only. Link: https://patch.msgid.link/20250720-ath12k-zero-brace-v1-1-d8c8ca9d40a8@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-07-14wifi: ath12k: Enable memory profile selection for QCN9274Aaradhana Sahu
The QCN9274 supports two memory profiles: a default profile and a low-memory profile. The driver signals the firmware to enable low-memory optimizations using the QMI initialization service. Add support to select the low-memory profile on system with less than 512 MB RAM. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250708181102.4111054-5-aaradhana.sahu@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-07-14wifi: ath12k: Refactor macros to use memory profile-based valuesAaradhana Sahu
Refactor macros to compute values dynamically at runtime based on the ath12k_mem_profile_based_param structure. Remove hardcoded logic to allow driver to operate more efficiently in memory-constrained platforms without significant functional impact. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250708181102.4111054-4-aaradhana.sahu@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-07-14wifi: ath12k: Remove redundant TID calculation for QCN9274Aaradhana Sahu
Currently, host sends num_tids (number of TID (Traffic Identifier)) value to firmware via WMI_INIT_CMD during WMI initialization. However, the firmware does not use this value, as it determines the number of TIDs using its own internal logic. Hence, remove the redundant num_tids calculation logic for QCN9274. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250708181102.4111054-3-aaradhana.sahu@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-07-14wifi: ath12k: Add a table of parameters entries impacting memory consumptionAaradhana Sahu
Introduce ath12k_mem_profile_based_param structure to define configuration parameters for both default and low-memory profiles. Add support for enabling the low-memory profile in the follow-up patch by making the following changes: - Reduce sizes for transmit, receive, and monitor descriptor rings. - Reduce transmit and receive descriptor count. - Limit the maximum number of virtual devices (vdevs) to 9. - Reduce the maximum number of client support per radio. Centralize these parameters in the ath12k_mem_profile_based_param structure to simplify switching between memory profiles. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250708181102.4111054-2-aaradhana.sahu@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-06-27wifi: ath12k: fix timeout while waiting for regulatory update during ↵Aditya Kumar Singh
interface creation During interface creation, following print is observed on the console - Timeout while waiting for regulatory update This occurs due to commit 906619a00967 ("wifi: ath12k: handle regulatory hints during mac registration"), which introduced a completion mechanism to synchronize the regulatory update process. The intent behind this change is to coordinate the timing between when the firmware sends regulatory data to the driver and when the driver processes that data. However, during interface addition, if the 6 GHz band is active, the driver invokes ath12k_regd_update() to apply the appropriate 6 GHz power mode regulatory settings. At this point, there is no interaction with the firmware, so the completion object is not reinitialized. As a result, wait_for_completion() eventually times out, leading to the observed error log message. Hence to fix this, move all complete() on regd_update_completed to complete_all(). The complete() function signals only once, causing any subsequent waits without reinitialization to timeout. In this scenario, since waiting is unnecessary, complete_all() can be used instead, ensuring that subsequent calls to wait without reinitialization will simply bail out and not actually wait. This approach is ideal because if the firmware is not involved, there is no need to wait for the completion event. However, if the firmware is involved, it is guaranteed that the completion will be reinitialized, and thus, it would wait. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1 Tested-by: Kang Yang <kang.yang@oss.qualcomm.com> Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Fixes: 906619a00967 ("wifi: ath12k: handle regulatory hints during mac registration") Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com> Link: https://patch.msgid.link/20250626-fix_timeout_during_interface_creation-v1-1-90a7fdc222d4@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-06-23wifi: ath12k: Add missing include of export.hJeff Johnson
Commit a934a57a42f6 ("scripts/misc-check: check missing #include <linux/export.h> when W=1") introduced a new check that is producing the following warning: drivers/net/wireless/ath/ath12k/core.c: warning: EXPORT_SYMBOL() is used, but #include <linux/export.h> is missing Add the missing #include to satisfy the check. Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250611-ath-unused-export-v1-5-c36819df7e7b@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-06-23wifi: ath12k: handle regulatory hints during mac registrationAditya Kumar Singh
If a regulatory notification is there in the system while the hardware is being registered, it attempts to set the new regulatory country. However, ath12k currently boots with a default country derived from the BDF. If this default country differs from the one provided in the notification, a race condition can occur while updating the regulatory information back to userspace. This potentially leads to driver having the incorrect regulatory applied. For example, suppose the regulatory domain for France (FR) is already applied, and then the driver is loaded with a BDF that has the United States (US) country programmed. When the driver finishes loading, the regulatory domain shown in phyX still reflects the US regulatory settings. This is incorrect, as the driver had already received a notification for FR during hardware registration, but failed to process it properly due to the race condition. The race condition exists during driver initialization and hardware registration: - On driver load, the firmware sends BDF-based country regulatory rules, which are stored in default_regd via ath12k_reg_handle_chan_list(). - During hardware registration, a regulatory notification is triggered through: ath12k_mac_hw_register() -> ieee80211_register_hw() -> wiphy_register() -> wiphy_regulatory_register() -> reg_call_notifier() This sends a country code to the firmware, which responds with updated regulatory rules. - After registration, ath12k_mac_hw_register() calls ath12k_regd_update(), which copies default_regd and passes it to the upper layers. The race occurs between the firmware's response and the execution of ath12k_regd_update(). If the firmware's new rules are processed before the update call, the correct values are used. Otherwise, outdated boot-time country settings are exposed to userspace. To resolve this issue, introduce a completion mechanism within the hardware group (ah). Trigger this completion whenever a regulatory change is requested from the firmware. Then, in ath12k_regd_update(), wait for the firmware to complete its regulatory processing before proceeding with the update. This ensures that during driver load, the default country is processed first. However, before ath12k_regd_update() is called, the new regulatory notification will have already been received by the driver. As a result, it will wait for the firmware's regulatory processing to complete, and only the final, correct regulatory domain will be updated to userspace. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1 Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250617-handle_user_regd_update_hints_during_insmod-v2-1-10a6a48efe81@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-06-23wifi: ath12k: update channel list in worker when wait flag is setKang Yang
With previous patch [1], ath12k_reg_update_chan_list() will be called during reg_process_self_managed_hint(). reg_process_self_managed_hint() will hold rtnl_lock all the time. But ath12k_reg_update_chan_list() may increase the occupation time of rtnl_lock, because when wait flag is set, wait_for_completion_timeout() will be called during 11d/hw scan. Should minimize the occupation time of rtnl_lock as much as possible to avoid interfering with rest of the system. So move the update channel list operation to a new worker, so that wait_for_completion_timeout() won't be called with the rtnl_lock held. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Fixes: f335295aa29c ("wifi: ath12k: avoid deadlock during regulatory update in ath12k_regd_update()") #[1] Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com> Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com> Link: https://patch.msgid.link/20250605082528.701-1-kang.yang@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-06-17wifi: ath12k: don't use static variables in ath12k_wmi_fw_stats_process()Baochen Qiang
Currently ath12k_wmi_fw_stats_process() is using static variables to count firmware stat events. Taking num_vdev as an example, if for whatever reason (say ar->num_started_vdevs is 0 or firmware bug etc.) the following condition (++num_vdev) == total_vdevs_started is not met, is_end is not set thus num_vdev won't be cleared. Next time when firmware stats is requested again, even if everything is working fine, failure is expected due to the condition above will never be satisfied. The same applies to num_bcn as well. Change to use non-static counters and reset them each time before firmware stats is requested. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Tested-on: QCN9274 hw2.0 WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1 Fixes: e367c924768b ("wifi: ath12k: Request vdev stats from firmware") Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Link: https://patch.msgid.link/20250612-ath12k-fw-fixes-v1-3-12f594f3b857@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-06-17wifi: ath12k: avoid burning CPU while waiting for firmware statsBaochen Qiang
ath12k_mac_get_fw_stats() is busy polling fw_stats_done flag while waiting firmware finishing sending all events. This is not good as CPU is monopolized and kept burning during the wait. Change to the completion mechanism to fix it. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Tested-on: QCN9274 hw2.0 WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1 Fixes: e367c924768b ("wifi: ath12k: Request vdev stats from firmware") Reported-by: Grégoire Stein <gregoire.s93@live.fr> Closes: https://lore.kernel.org/ath12k/AS8P190MB120575BBB25FCE697CD7D4988763A@AS8P190MB1205.EURP190.PROD.OUTLOOK.COM/ Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Tested-by: Grégoire Stein <gregoire.s93@live.fr> Link: https://patch.msgid.link/20250612-ath12k-fw-fixes-v1-2-12f594f3b857@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-06-07wifi: ath12k: fix uaf in ath12k_core_init()Miaoqing Pan
When the execution of ath12k_core_hw_group_assign() or ath12k_core_hw_group_create() fails, the registered notifier chain is not unregistered properly. Its memory is freed after rmmod, which may trigger to a use-after-free (UAF) issue if there is a subsequent access to this notifier chain. Fixes the issue by calling ath12k_core_panic_notifier_unregister() in failure cases. Call trace: notifier_chain_register+0x4c/0x1f0 (P) atomic_notifier_chain_register+0x38/0x68 ath12k_core_init+0x50/0x4e8 [ath12k] ath12k_pci_probe+0x5f8/0xc28 [ath12k] pci_device_probe+0xbc/0x1a8 really_probe+0xc8/0x3a0 __driver_probe_device+0x84/0x1b0 driver_probe_device+0x44/0x130 __driver_attach+0xcc/0x208 bus_for_each_dev+0x84/0x100 driver_attach+0x2c/0x40 bus_add_driver+0x130/0x260 driver_register+0x70/0x138 __pci_register_driver+0x68/0x80 ath12k_pci_init+0x30/0x68 [ath12k] ath12k_init+0x28/0x78 [ath12k] Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Fixes: 6f245ea0ec6c ("wifi: ath12k: introduce device group abstraction") Signed-off-by: Miaoqing Pan <miaoqing.pan@oss.qualcomm.com> Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com> Link: https://patch.msgid.link/20250604055250.1228501-1-miaoqing.pan@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-05-19wifi: ath12k: Reorder and relocate the release of resources in ↵Yingying Tang
ath12k_core_deinit() Ath12k panic notifier is registered in driver loading process. But it is not unregistered if ATH12K_FLAG_QMI_FAIL is set(e.g. load BDF failed) and unload driver. It causes a dirty node in panic notifier list since ath12k panic notifier is not unregistered from list but the buffer of this node is freed in driver unloading process. If load driver again there will be a page fault error due to this dirty node in panic notifier list. This issue is caused by asymmetry between ath12k_core_init() and ath12k_core_deinit(). Reorder and relocate the release of resources in ath12k_core_deinit() to avoid this asymmetry issue. Call Trace: <TASK> ? show_regs+0x67/0x70 ? __die_body+0x20/0x70 ? __die+0x2b/0x40 ? page_fault_oops+0x15d/0x500 ? search_bpf_extables+0x63/0x90 ? notifier_chain_register+0x21/0xe0 ? search_exception_tables+0x5f/0x70 ? kernelmode_fixup_or_oops.isra.0+0x61/0x80 ? __bad_area_nosemaphore+0x179/0x240 ? bad_area_nosemaphore+0x16/0x20 ? do_user_addr_fault+0x312/0x7f0 ? prb_read_valid+0x1c/0x30 ? exc_page_fault+0x78/0x180 ? asm_exc_page_fault+0x27/0x30 ? notifier_chain_register+0x21/0xe0 ? notifier_chain_register+0x55/0xe0 atomic_notifier_chain_register+0x2c/0x50 ath12k_core_init+0x7e/0x110 [ath12k] ath12k_pci_probe+0xaba/0xba0 [ath12k] Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0-02903-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Fixes: 809055628bce8 ("wifi: ath12k: add panic handler") Signed-off-by: Yingying Tang <quic_yintang@quicinc.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250423055650.16230-2-quic_yintang@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-05-19wifi: ath12k: print device dp stats in debugfsVinith Kumar R
Print the data path related device specific stats in debugfs. These device_dp_stats are exposed in the ath12k debugfs directory. Output of device_dp_stats: root@CDCWLEX0799743-LIN:/home/qctest# cat /sys/kernel/debug/ath12k/pci-0000\:58\:00.0/device_dp_stats DEVICE RX STATS: err ring pkts: 0 Invalid RBM: 0 RXDMA errors: Overflow: 0 MPDU len: 0 FCS: 0 Decrypt: 0 TKIP MIC: 0 Unencrypt: 0 MSDU len: 0 MSDU limit: 0 WiFi parse: 0 AMSDU parse: 0 SA timeout: 0 DA timeout: 0 Flow timeout: 0 Flush req: 0 AMSDU frag: 0 Multicast echo: 0 AMSDU mismatch: 0 Unauth WDS: 0 AMSDU or WDS: 0 REO errors: Desc addr zero: 0 Desc inval: 0 AMPDU in non BA: 0 Non BA dup: 0 BA dup: 0 Frame 2k jump: 0 BAR 2k jump: 0 Frame OOR: 155 BAR OOR: 0 No BA session: 0 Frame SN equal SSN: 0 PN check fail: 0 2k err: 0 PN err: 0 Desc blocked: 0 HAL REO errors: ring0: 0 ring1: 0 ring2: 0 ring3: 0 ring4: 0 ring5: 0 ring6: 0 ring7: 0 DEVICE TX STATS: TCL Ring Full Failures: ring0: 0 ring1: 0 ring2: 0 ring3: 0 Misc Transmit Failures: 0 tx_wbm_rel_source: 0:986 1:0 2:0 3:57 4:0 tqm_rel_reason: 0:1043 1:0 2:0 3:0 4:0 5:0 6:0 7:0 8:0 9:0 10:0 11:0 12:0 13:0 14:0 fw_tx_status: 0:57 1:0 2:0 3:0 4:0 5:0 6:0 tx_enqueued: 0:329 1:145 2:464 3:105 tx_completed: 0:329 1:145 2:464 3:105 radio0 tx_pending: 0 REO Rx Received: Ring1: 0:201 1:0 2:0 Ring2: 0:0 1:0 2:0 Ring3: 0:6152 1:0 2:0 Ring4: 0:9 1:0 2:0 Ring5: 0:0 1:0 2:0 Ring6: 0:0 1:0 2:0 Ring7: 0:0 1:0 2:0 Ring8: 0:0 1:0 2:0 Rx WBM REL SRC Errors: TQM: 0:0 1:0 2:0 Rxdma: 0:0 1:0 2:0 Reo: 0:155 1:0 2:0 FW: 0:0 1:0 2:0 SW: 0:0 1:0 2:0 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Vinith Kumar R <quic_vinithku@quicinc.com> Signed-off-by: Nithyanantham Paramasivam <nithyanantham.paramasivam@oss.qualcomm.com> Reviewed-by: Mahendran P <quic_mahep@quicinc.com> Link: https://patch.msgid.link/20250425012802.698914-4-nithyanantham.paramasivam@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-05-19wifi: ath12k: change soc name to device nameVinith Kumar R
To have consistent nomenclature, replace the use of the term "soc" with the term "device". Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Vinith Kumar R <quic_vinithku@quicinc.com> Signed-off-by: Nithyanantham Paramasivam <nithyanantham.paramasivam@oss.qualcomm.com> Reviewed-by: Mahendran P <quic_mahep@quicinc.com> Link: https://patch.msgid.link/20250425012802.698914-2-nithyanantham.paramasivam@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-05-16wifi: ath12k: read country code from SMBIOS for WCN7850Wen Gong
Read the country code from SMBIOS and send it to the firmware. The firmware will then indicate the regulatory domain information for the country code, which ath12k will use. dmesg: [ 1242.637253] ath12k_pci 0000:02:00.0: worldwide regdomain setting from SMBIOS [ 1242.637259] ath12k_pci 0000:02:00.0: bdf variant name not found. [ 1242.637261] ath12k_pci 0000:02:00.0: SMBIOS bdf variant name not set. [ 1242.927543] ath12k_pci 0000:02:00.0: set current country pdev id 0 alpha2 00 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-02582-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1 Signed-off-by: Wen Gong <quic_wgong@quicinc.com> Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com> Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com> Link: https://patch.msgid.link/20250417024227.1712-1-kang.yang@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-04-17wifi: ath12k: fix node corruption in ar->arvifs listMaharaja Kennadyrajan
In current WLAN recovery code flow, ath12k_core_halt() only reinitializes the "arvifs" list head. This will cause the list node immediately following the list head to become an invalid list node. Because the prev of that node still points to the list head "arvifs", but the next of the list head "arvifs" no longer points to that list node. When a WLAN recovery occurs during the execution of a vif removal, and it happens before the spin_lock_bh(&ar->data_lock) in ath12k_mac_vdev_delete(), list_del() will detect the previously mentioned situation, thereby triggering a kernel panic. The fix is to remove and reinitialize all vif list nodes from the list head "arvifs" during WLAN halt. The reinitialization is to make the list nodes valid, ensuring that the list_del() in ath12k_mac_vdev_delete() can execute normally. Call trace: __list_del_entry_valid_or_report+0xd4/0x100 (P) ath12k_mac_remove_link_interface.isra.0+0xf8/0x2e4 [ath12k] ath12k_scan_vdev_clean_work+0x40/0x164 [ath12k] cfg80211_wiphy_work+0xfc/0x100 process_one_work+0x164/0x2d0 worker_thread+0x254/0x380 kthread+0xfc/0x100 ret_from_fork+0x10/0x20 The change is mostly copied from the ath11k patch: https://lore.kernel.org/all/20250320053145.3445187-1-quic_stonez@quicinc.com/ Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1 Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices") Signed-off-by: Maharaja Kennadyrajan <maharaja.kennadyrajan@oss.qualcomm.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250416021724.2162519-1-maharaja.kennadyrajan@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-04-15wifi: ath12k: support MLO as well if single_chip_mlo_support flag is setBaochen Qiang
Currently firmware MLO capability is validated via firmware IE, however WCN7850 firmware does not support this method but instead advertises MLO by single_chip_mlo_support bit in QMI phy capability message. Change to consider single_chip_mlo_support bit as well for MLO capability validation. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-3-3801132ca2c3@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-04-15wifi: ath12k: introduce ath12k_fw_feature_supported()Baochen Qiang
There are several places checking if a specific bit set in ab->fw.fw_features, and in an upcoming patch additional check needs to be added at all places. Introduce a new helper ath12k_fw_feature_supported() to avoid code duplication. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-1-3801132ca2c3@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-04-11wifi: ath12k: reset MLO global memory during recoveryAditya Kumar Singh
When operating with multiple devices grouped together, the firmware stores data related to the state machine of each partner device in the MLO global memory region. If the firmware crashes, it updates the state to 'crashed'. During recovery, this memory is shared with the firmware again, and upon detecting the 'crashed' state, it reasserts. This leads to a loop of firmware asserts and it never recovers. Hence to fix this issue, once all devices in the group have been asserted and powered down, reset the MLO global memory region. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-9-95e7bf048595@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-04-11wifi: ath12k: handle ath12k_core_reset() with hardware groupingAditya Kumar Singh
Currently, in ath12k_core_reset(), the device is powered up immediately after a power down. However, with hardware grouping, when one device asserts, all partner devices also asserts. If there is a delay in processing these asserts, by the time this device powers up, other devices might still be asserting, leading to an overall recovery failure. To prevent this issue, ensure all asserts for a group are processed before initiating the power-up sequence. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-8-95e7bf048595@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-04-11wifi: ath12k: handle ath12k_core_restart() with hardware groupingAditya Kumar Singh
Currently, when ath12k_core_restart() is called and the ab->is_reset flag is set, it invokes ieee80211_restart_hw() for all hardware in the same group. However, other hardware might still be in the recovery process, making this call inappropriate with grouping into picture. To address this, add a condition to check if the group is ready. If the group is not ready, do not call ieee80211_restart_hw(). Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-7-95e7bf048595@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-04-11wifi: ath12k: fix ath12k_core_pre_reconfigure_recovery() with groupingAditya Kumar Singh
Currently, ath12k_core_pre_reconfigure_recovery() reconfigures all radios within the same group. During grouping and driver going for a recovery, this function is called as many times as there are devices in the group. Consequently, it performs the same reconfiguration multiple times, which is unnecessary. To prevent this, add a check to continue if the action has already been taken. To simplify the management of various flags, the reason for hardware queues being stopped is used as a check instead of introducing a new flag. While at it, also add missing wiphy locks. Wiphy lock is required since ath12k_mac_drain_tx() which is called by ath12k_core_pre_reconfigure_recovery() needs this lock to be held by the caller. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-6-95e7bf048595@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-04-11wifi: ath12k: fix ATH12K_FLAG_REGISTERED flag handlingAditya Kumar Singh
Commit a5686ae820fa ("wifi: ath12k: move ATH12K_FLAG_REGISTERED handling to ath12k_mac_register()") relocated the setting of the ATH12K_FLAG_REGISTERED flag to the ath12k_mac_register() function. However, this function only accesses the first device (ab) via ag->ab[0], resulting in the flag being set only for the first device in the group. Similarly, ath12k_mac_unregister() only unsets the flag for the first device. The flag should actually be set for all devices in the group to avoid issues during recovery. Hence, move setting and clearing of this flag in the function ath12k_core_hw_group_start() and ath12k_core_hw_group_stop() respectively. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Fixes: a5686ae820fa ("wifi: ath12k: move ATH12K_FLAG_REGISTERED handling to ath12k_mac_register()") Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-4-95e7bf048595@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-04-11wifi: ath12k: add reference counting for core attachment to hardware groupAditya Kumar Singh
Currently, driver does not manage reference counting for attaching and detaching cores to/from hardware groups. This can lead to issues when multiple cores are involved. Or with same core, attach/detach is called multiple times back to back. Fix this issue by using reference counting. With that, it is now ensured that the core is properly attached or detached from the hardware group and even back to back calls will not alter the count. Additionally, add some debug logs during the attachment and detachment events for better debugging and tracking. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-2-95e7bf048595@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-04-02wifi: ath12k: store and send country code to firmware after recoveryWen Gong
Currently ath12k does not send the country code to firmware after device recovery. As a result the country code will be the default one which is reported from firmware. Country code is important, so ath12k also need to restore it to the value which was used before recovery. This is only needed for platforms which support the current_cc_support hardware parameter. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Wen Gong <quic_wgong@quicinc.com> Signed-off-by: Kang Yang <quic_kangyang@quicinc.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250401020840.357-5-quic_kangyang@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-04-02wifi: ath12k: add 11d scan offload supportWen Gong
The flow of 11d scan is: 1. trigger 11d scan. 2. receive, parse, and update 11d scan result. 3. stop 11d scan. So need to add handler for WMI_11D_SCAN_START_CMDID and WMI_11D_SCAN_STOP_CMDID to trigger/stop 11d scan. Add process of WMI event WMI_11D_NEW_COUNTRY_EVENTID for 11d scan result. There are two points that need to be noted: 1. The 11d scan priority is 'MEDIUM' in firmware, the hw scan priority is 'LOW'. When 11d scan is running, hw scan will be canceled. To avoid this, change the hw scan priority to 'MEDIUM' when 11d scan is running. 2. Need to add wait_for_completion_timeout() for scan.complete in ath12k_reg_update_chan_list() because 11d scan will cost more than 5 seconds. Due to another existing wait in ath12k_scan_stop(), there will be two scan.complete in different threads. Therefore use complete_all() instead of complete() for scan.complete. complete_all() can work well when it is only one thread wait for scan.complete. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Wen Gong <quic_wgong@quicinc.com> Signed-off-by: Kang Yang <quic_kangyang@quicinc.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250401020840.357-4-quic_kangyang@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-03-27wifi: ath12k: add monitor interface support on QCN9274P Praneesh
Currently, the monitor interface is not supported. To support the monitor interface, configure the monitor vdev state identifier, configure the HTT filter setup, subscribe the mac80211 NO_VIRTUAL_MONITOR feature, remove the VIRTUAL_MONITOR handler procedures since align to NO_VIRTUAL_MONITOR feature and prevent monitor interface to transmit packet. Therefore, add these procedures to add monitor interface support and enable the monitor interface support on the QCN9274 platform through the hardware parameter. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250324062518.2752822-11-quic_periyasa@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-03-25wifi: ath12k: enable ath12k AHB supportBalamurugan S
Currently only PCI devices are supported in Ath12k driver. Refactor Ath12k module_init and module_exit to include Ath12k AHB support. Add Ath12k AHB support in Kconfig with dependency on Remoteproc driver. Ath12k AHB support relies on remoteproc driver for firmware download, power up/down etc. Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1 Signed-off-by: Balamurugan S <quic_bselvara@quicinc.com> Co-developed-by: P Praneesh <quic_ppranees@quicinc.com> Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Link: https://patch.msgid.link/20250321-ath12k-ahb-v12-13-bb389ed76ae5@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-03-25wifi: ath12k: add support for fixed QMI firmware memoryRaj Kumar Bhagat
IPQ5332 firmware supports only fixed QMI firmware memory. Hence, add support to read reserved fixed memory region from device-tree and provide the reserved memory segments for firmware to use during QMI firmware memory request. Note that the ability to set the fixed memory will be introduced in a subsequent patch. Currently, the flag remains unset by default, ensuring that existing chipsets are unaffected. Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1 Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Link: https://patch.msgid.link/20250321-ath12k-ahb-v12-7-bb389ed76ae5@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-03-17wifi: ath12k: move firmware stats out of debugfsAditya Kumar Singh
Currently, firmware stats, comprising pdev, vdev and beacon stats are part of debugfs. In firmware pdev stats, firmware reports the final Tx power used to transmit each packet. If driver wants to know the final Tx power being used at firmware level, it can leverage from firmware pdev stats. Move firmware stats out of debugfs context in order to leverage the final Tx power reported in it even when debugfs is disabled. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com> Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com> Reviewed-by: Mahendran P <quic_mahep@quicinc.com> Link: https://patch.msgid.link/20250306102215.1300522-2-rameshkumar.sundaram@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-02-18wifi: ath12k: cleanup ath12k_mac_mlo_ready()Ethan Carter Edwards
There is a possibility for an uninitialized *ret* variable to be returned in some code paths. This explicitly returns 0 without an error. Also removes goto that returned *ret* and simply returns in place. Closes: https://scan5.scan.coverity.com/#/project-view/63541/10063?selectedIssue=1642337 Fixes: b716a10d99a2 ("wifi: ath12k: enable MLO setup and teardown from core") Signed-off-by: Ethan Carter Edwards <ethan@ethancedwards.com> Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com> Link: https://patch.msgid.link/20250210-ath12k-uninit-v2-1-3596f28dd380@ethancedwards.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-02-11wifi: ath12k: Enable MLO for single split-phy PCI deviceAaradhana Sahu
The single split-phy PCI device can perform multi-link operation (MLO) within its own radio, and the MLO-supporting firmware also supports MLO for split-phy PCI devices. Therefore, enable MLO for the single split-phy PCI device. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250207050327.360987-4-quic_aarasahu@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-02-11wifi: ath12k: Enable MLO setup ready and teardown commands for single ↵Aaradhana Sahu
split-phy device When multi-link operation(MLO) is enabled through follow-up patches in the single split-phy device, the firmware expects hardware links (hw_links) information from the driver. If driver does not send WMI multi-link setup and ready command to the firmware during MLO setup for single split-phy device, the firmware will be unaware of the hw_links component of the multi-link operation. This may lead to firmware assert during multi-link association. Therefore, enable WMI setup, ready and teardown commands for single split-phy PCI device. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250207050327.360987-2-quic_aarasahu@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-02-11wifi: ath12k: Fix locking in "QMI firmware ready" error pathsBart Van Assche
If ag->mutex has been locked, unlock it before returning. If it has not been locked, do not unlock it before returning. These bugs have been detected by the Clang thread-safety analyzer. Cc: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Cc: Jeff Johnson <jeff.johnson@oss.qualcomm.com> Fixes: ee146e11b4d9 ("wifi: ath12k: refactor core start based on hardware group") Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com> Link: https://patch.msgid.link/20250206221317.3845663-1-bvanassche@acm.org Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-02-03wifi: ath12k: Adjust the timing to access ACPI tableLingbo Kong
Currently, the timing for accessing the ACPI table is inappropriate. Due to special ACPI requirements, the ACPI table must be obtained before downloading the board data file. Therefore, adjust the timing for accessing the ACPI table accordingly. This patch will not affect QCN9274, because only WCN7850 supports ACPI. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Link: https://patch.msgid.link/20250113074810.29729-4-quic_lingbok@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-02-03wifi: ath12k: Add Support for enabling or disabling specific features based ↵Lingbo Kong
on ACPI bitflag Currently, ath12k does not support enable or disable specific features by ACPI bitflag. To address this issue, obtain the ACPI bitflag value and use it to selectively enable or disable specific features. This patch will not affect QCN9274, because only WCN7850 supports ACPI. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Link: https://patch.msgid.link/20250113074810.29729-3-quic_lingbok@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-29wifi: ath12k: Fetch regdb.bin file from board-2.binAaradhana Sahu
Currently, ath12k_core_fetch_regdb() finds regdb.bin file through board id's but in board-2.bin file regdb.bin file is present with default board id because of which regdb.bin is not fetched. Add support to fetch regdb.bin file from board-2.bin through default board id. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com> Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com> Link: https://patch.msgid.link/20250116032835.118397-1-quic_aarasahu@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-22wifi: ath12k: Disable MLO in Factory Test ModeAaradhana Sahu
Factory test mode(FTM) is supported only in non-MLO(multi-link operation) mode. Therefore, disable MLO when driver boots in FTM mode. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com> Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com> Link: https://patch.msgid.link/20250119083657.1937557-5-quic_aarasahu@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-22wifi: ath12k: add factory test mode supportAaradhana Sahu
Add support to process factory test mode commands(FTM) for calibration. By default firmware start with MISSION mode and to process the FTM commands firmware needs to be restarted in FTM mode using module parameter ftm_mode. The pre-request is all the radios should be down before starting the test. All ath12k test mode interface related commands specified in enum ath_tm_cmd. When start command ATH_TM_CMD_TESTMODE_START is received, ar state is set to test Mode and FTM daemon sends test mode command to wifi driver via cfg80211. Wifi driver sends these command to firmware as wmi events. If it is segmented commands it will be broken down into multiple segments and encoded with TLV header else it is sent to firmware as it is. Firmware response via UTF events, wifi driver creates skb and send to cfg80211, cfg80211 sends firmware response to FTM daemon via netlink message. Command to boot in ftm mode insmod ath12k ftm_mode=1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com> Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com> Link: https://patch.msgid.link/20250119083657.1937557-4-quic_aarasahu@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-14wifi: ath12k: Remove ath12k_get_num_hw() helper functionKarthikeyan Periyasamy
Currently, the ath12k_get_num_hw() helper function takes the device handle as an argument. Here, the number of hardware is retrieved from the group handle. Demanding the device handle from the caller is unnecessary since in some cases the group handle is already available. Additionally, there is no longer a need for multiple indirections to get the number of hardware. Therefore, remove this helper function and directly use ag->num_hw. This change also fixes the below Smatch static checker warning. Smatch warning: ath12k_mac_destroy() error: we previously assumed 'ab' could be null Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/ath12k/3e705de0-67d1-4437-97ff-4828d83ae2af@stanley.mountain/ Closes: https://scan7.scan.coverity.com/#/project-view/52682/11354?selectedIssue=1602340 Fixes: a343d97f27f5 ("wifi: ath12k: move struct ath12k_hw from per device to group") Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Acked-by: Kalle Valo <kvalo@kernel.org> Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com> Link: https://patch.msgid.link/20250112071630.4059410-4-quic_periyasa@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-14wifi: ath12k: Refactor the ath12k_hw get helper function argumentKarthikeyan Periyasamy
Currently, ath12k_hw is placed inside the ath12k_hw_group. However, the ath12k_hw get helper function takes the device handle and the index as parameters. Here, the index parameter is specific to the group handle. Therefore, change this helper function argument from the device handle to the group handle. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com> Acked-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20250112071630.4059410-3-quic_periyasa@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2024-12-16wifi: ath12k: add ATH12K_FW_FEATURE_MLO capability firmware featureAditya Kumar Singh
To maintain backward compatibility with older firmware versions, introduce a new feature bit, ATH12K_FW_FEATURE_MLO, to identify whether the firmware supports MLO. If the firmware-X.bin does not have this bit advertised in the feature, then MLO capability in the host will be disabled. This applies only for QCN9274 chipsets. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://patch.msgid.link/20241211154358.776279-6-kvalo@kernel.org Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2024-12-16wifi: ath12k: add helper function to init partner cmem configurationKarthikeyan Periyasamy
In the Inter Multi-Link Operation, the primary device is expected to receive the partner device buffer. Therefore, each device initializes the partner device buffer in their cmem configuration. So add a helper function to initialize the partner device buffer in their cmem configuration. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://patch.msgid.link/20241209185421.376381-4-kvalo@kernel.org Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2024-12-16wifi: ath12k: enable MLO setup and teardown from coreKarthikeyan Periyasamy
In case of multi device group abstraction, host has to exchange the multi-link operation commands such as setup and ready to firmware before registering the device group to mac80211. The multi-link operation commands - setup, ready and teardown are necessary for many commands such as WMI_PEER_ASSOC_CMD, WMI_BCN_TMPL_CMD in case of multi-link interfaces. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://patch.msgid.link/20241211153432.775335-8-kvalo@kernel.org Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2024-12-16wifi: ath12k: parse multiple device information from Device TreeRaj Kumar Bhagat
Currently, a single device is part of the device group abstraction. However, for multi-link operations, multiple devices need to be combined. This multi-device grouping is done via WSI (WLAN Serial Interface), which is described in the Device Tree. Information about different WSI groups and the number of devices involved in each group can be parsed from the Device Tree. Add changes to parse the Device Tree and determine WSI information, such as the different WSI groups and the number of devices per WSI group. Assign WSI index zero to the WSI controller device (to synchronize the clock among the devices within the WSI group), and increment the WSI index of each device in the order of the WSI connection. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Co-developed-by: Harshitha Prem <quic_hprem@quicinc.com> Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com> Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://patch.msgid.link/20241211153432.775335-3-kvalo@kernel.org Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2024-12-05wifi: ath12k: introduce mlo_capable flag for device groupKarthikeyan Periyasamy
Currently, during mac80211 allocate and register single device is considered for the registration. But, in future, during multi device group abstraction is introduced, all the devices has to be combined together as a single abstraction and then hardware should be allocated. All the devices in the group should be combined together only if it supports inter device mlo capability. The decision of whether to combine the devices or not can be based on the mlo capability flag in ath12k_hw_group. By default, mlo_capable flag in the group would be set as false. During QMI PHY capability exchange, only when we have more than one chip in the group or if one chip, then that chip supports inter MLO, then mlo_capable flag in the group will be enabled. Add changes to introduce mlo_capable flag for device group and refactor ath12k_mac_hw_allocate() api based on device group (ag) rather than device (ab). Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://patch.msgid.link/20241204163216.433795-8-kvalo@kernel.org Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2024-12-05wifi: ath12k: send QMI host capability after device group is readyKarthikeyan Periyasamy
QMI host capability has the information regarding MLO parameters such as device_id, MLO capability, group id and the information of each devices involved in the group and sent immediately on QMI server arrive event. Currently, only one device is involved in the group and hence, single device information is sent as part of MLO capability of host. But, in future when multi device group abstraction is introduced, host should send all the device information involved in the group as part of QMI MLO host capability rather than single device. Hence, sending QMI host capability immediately on server arrive of a device might not be ideal for multi device group abstraction as the details of other devices in the group would not be available. Hence, once QMI server arrive event is received, request for QMI PHY capabilities of device, and defer the host capability send for that device. After QMI PHY capability is received for all the devices in the group trigger the host capability event for the deferred devices in the group. Hence, add changes to defer the QMI host capability event until the device group is ready and then resume the QMI exchange for all the device with host capabilities. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://patch.msgid.link/20241204163216.433795-7-kvalo@kernel.org Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
generated by cgit v1.2.3 (git 2.46.0) at 2025-12-10 15:35:56 +0000