| Age | Commit message (Collapse) | Author |
|---|
|
MediaTek has asked to switch from the ISC license to BSD-3-Clause-Clear,
in order to improve clarity and the legal integrity of the code.
The BSD-3-Clause license includes the "no endorsement" clause, which is
important for protecting the reputation of the original authors and
contributors by preventing unauthorized use of their names for endorsement
purposes.
This clause is absent in the BSD-2-Clause license, which is more permissive
but lacks this specific protection.
This change also cleans up the license of some Kconfig/Makefile files,
which were accidentally marked as GPL.
The GPL 2.0 remains in use on mt76x0, as well as two source files in mt7615
for which the license situation still needs to be clarified.
Link: https://patch.msgid.link/20251008104250.46292-2-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The commit 22b980badc0f ("mt76: add functions for parsing rate power limits
from DT") introduced generic support for rates limits in the devicetree.
But the mt7915 supports beamforming and has another table for configuring
the backoff limits. These can be configured in the DT with the paths-*
properties. The path-*-bf are the ones relevant for beamforming and the
ones without -bf suffix for "traditional" path backoff.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Sven Eckelmann (Plasma Cloud) <se@simonwunderlich.de>
Link: https://patch.msgid.link/20251007-backoff-table-support-v3-3-fd6e2684988f@simonwunderlich.de
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
In vendor driver, size of group cal and dpd cal for mt7981 includes 6G
although the chip doesn't support it.
mt76 doesn't take this into account which results in reading from the
incorrect offset.
For devices with precal, this would lead to lower bitrate.
Fix this by aligning groupcal size with vendor driver and switch to
freq_list_v2 in mt7915_dpd_freq_idx in order to get the correct offset.
Below are iwinfo of the test device with two clients connected
(iPhone 16, Intel AX210).
Before :
Mode: Master Channel: 36 (5.180 GHz) HT Mode: HE80
Center Channel 1: 42 2: unknown
Tx-Power: 23 dBm Link Quality: 43/70
Signal: -67 dBm Noise: -92 dBm
Bit Rate: 612.4 MBit/s
Encryption: WPA3 SAE (CCMP)
Type: nl80211 HW Mode(s): 802.11ac/ax/n
Hardware: embedded [MediaTek MT7981]
After:
Mode: Master Channel: 36 (5.180 GHz) HT Mode: HE80
Center Channel 1: 42 2: unknown
Tx-Power: 23 dBm Link Quality: 43/70
Signal: -67 dBm Noise: -92 dBm
Bit Rate: 900.6 MBit/s
Encryption: WPA3 SAE (CCMP)
Type: nl80211 HW Mode(s): 802.11ac/ax/n
Hardware: embedded [MediaTek MT7981]
Tested-on: mt7981 20240823
Fixes: 19a954edec63 ("wifi: mt76: mt7915: add mt7986, mt7916 and mt7981 pre-calibration")
Signed-off-by: Zhi-Jun You <hujy652@gmail.com>
Link: https://patch.msgid.link/20250909064824.16847-1-hujy652@gmail.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Cross-merge networking fixes after downstream PR (net-6.16-rc6-2).
No conflicts.
Adjacent changes:
drivers/net/wireless/mediatek/mt76/mt7925/mcu.c
c701574c5412 ("wifi: mt76: mt7925: fix invalid array index in ssid assignment during hw scan")
b3a431fe2e39 ("wifi: mt76: mt7925: fix off by one in mt7925_mcu_hw_scan()")
drivers/net/wireless/mediatek/mt76/mt7996/mac.c
62da647a2b20 ("wifi: mt76: mt7996: Add MLO support to mt7996_tx_check_aggr()")
dc66a129adf1 ("wifi: mt76: add a wrapper for wcid access with validation")
drivers/net/wireless/mediatek/mt76/mt7996/main.c
3dd6f67c669c ("wifi: mt76: Move RCU section in mt7996_mcu_add_rate_ctrl()")
8989d8e90f5f ("wifi: mt76: mt7996: Do not set wcid.sta to 1 in mt7996_mac_sta_event()")
net/mac80211/cfg.c
58fcb1b4287c ("wifi: mac80211: reject VHT opmode for unsupported channel widths")
037dc18ac3fb ("wifi: mac80211: add support for storing station S1G capabilities")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Several places use rcu_dereference to get a wcid entry without validating
if the index exceeds the array boundary. Fix this by using a helper function,
which handles validation.
Link: https://patch.msgid.link/20250707154702.1726-1-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Restart the MCU and release the patch semaphore before loading the MCU
patch firmware from the host.
This fixes failures upon error recovery in case the semaphore was
previously taken and never released by the host.
This happens from time to time upon triggering a full-chip error
recovery. Under this circumstance, the hardware restart fails and the
radio is rendered inoperational.
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://patch.msgid.link/20250402004528.1036715-3-mail@david-bauer.net
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The default timeout set in mt76_connac2_mcu_fill_message of 20 seconds
leads to excessive stalling in case messages are lost.
Testing showed that a smaller timeout of 5 seconds is sufficient in
normal operation.
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://patch.msgid.link/20250402004528.1036715-1-mail@david-bauer.net
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Increase the timeout for MCU_EXT_CMD_EFUSE_BUFFER_MODE command.
Regular retries upon hardware-recovery have been observed. Increasing
the timeout slightly remedies this problem.
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://patch.msgid.link/20250402004528.1036715-2-mail@david-bauer.net
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The definition of MT_RX_SEL (for rdd_rx_sel) is mixed with the
definition of HWRDD idx.
For example, MT_RX_SEL2 is for background HWRDD idx, not an option
of rdd_rx_sel.
Therefore, add mt7915_get_rdd_idx as a helper function to get the
HWRDD idx for each variants.
Additionally, remove some parts of the code inherited from the legacy
chips.
For instance,
1. rdd_state is used for single-band-dual-HWRDD chips (for 80+80),
especially the 76xx series.
2. rdd_rx_sel is also used for single-band-dual-HWRDD chips
rx_sel = 0 => RDD0 for WF0, RDD1 for WF2
rx_sel = 1 => RDD0 for WF1, RDD1 for WF3
Chip Variants | 5G rdd idx(=bandidx)| Background rdd idx
-------------------------------|---------------------|-------------------
MT7915A | 0 | 2
MT7915D | 1 | 2
MT7916 2G + 5G (2T2R+1R) | 1 | 2
MT7916 2G + 5G (3T3R) | 1 | N/A
MT7981 2G + 5G | 1 | N/A
MT7986 2G + 5G (one adie DBDC) | 1 | N/A
MT7986 5G (one adie) | 1 (bandidx=MT_BAND1)| N/A
MT7986 2G + 5G (dual adie) | 1 | N/A
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Reviewed-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250320015918.3948643-1-StanleyYP.Wang@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Some of the variants do not support background radar, so add a
helper to report background radar capability.
For mt7916, only the variant of 5G 2T2R + 1R supports background
radar.
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Reviewed-by: Shayne Chen <shayne.chen@mediatek.com>
Link: https://patch.msgid.link/20250320015909.3948612-1-StanleyYP.Wang@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Refactor for making use of mt76_get_power_bound instead of the specific
mt7915_get_power_bound, since we need this for other chipsets as well
when calculating txpower
Signed-off-by: Razvan Grigore <razvan.grigore@vampirebyte.ro>
Link: https://patch.msgid.link/20250211081247.5892-5-razvan.grigore@vampirebyte.ro
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Pass in struct ieee80211_bss_conf in order to use link specific data.
Link: https://patch.msgid.link/20250102163508.52945-19-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
This allows faster recovery from firmware issues
Link: https://patch.msgid.link/20241230194202.95065-7-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The need to retry a command is really uncommon. Reduce the retries to 1 to
speed up recovery from firmware issues.
Link: https://patch.msgid.link/20241230194202.95065-6-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
This helps to make STA airtime counters more accurate.
Signed-off-by: Chad Monroe <chad@monroe.io>
Suggested-by: Ryder Lee <ryder.lee@mediatek.com>
Link: https://patch.msgid.link/026380cec180261956b983cbdb009605867bcd8d.1732596478.git.chad@monroe.io
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
mt76 patches for 6.12
- fixes
- mt7915 .sta_state support
- mt7915 hardware restart improvements
|
|
- use reconfig_complete to restart mac_work / queues
- reset full wtbl after firmware init
- clear wcid and vif mask to avoid leak
- fix sta poll list corruption
Link: https://patch.msgid.link/20240827093011.18621-19-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
On MT7915, MCU hangs do not trigger watchdog interrupts, so they can only
be detected through MCU message timeouts. Ensure that the hardware gets
restarted when that happens in order to prevent a permanent stuck state.
Link: https://patch.msgid.link/20240827093011.18621-15-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
In some cases MCU messages can get lost. Instead of failing completely,
attempt to recover by re-sending them.
Link: https://patch.msgid.link/20240827093011.18621-14-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Allows adding stations before assoc, though they are not passed to the
firmware yet at that point.
Link: https://patch.msgid.link/20240827093011.18621-12-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Preparation for improvements to sta handling. No functional changes.
Link: https://patch.msgid.link/20240827093011.18621-10-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Avoids firmware race condition.
Link: https://patch.msgid.link/20240827093011.18621-7-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Currently DFS works under assumption there could be only one channel
context in the hardware. Hence, drivers just calls the function
ieee80211_radar_detected() passing the hardware structure. However, with
MLO, this obviously will not work since number of channel contexts will be
more than one and hence drivers would need to pass the channel information
as well on which the radar is detected.
Also, when radar is detected in one of the links, other link's CAC should
not be cancelled.
Hence, in order to support DFS with MLO, do the following changes -
* Add channel context conf pointer as an argument to the function
ieee80211_radar_detected(). During MLO, drivers would have to pass on
which channel context conf radar is detected. Otherwise, drivers could
just pass NULL.
* ieee80211_radar_detected() will iterate over all channel contexts
present and
* if channel context conf is passed, only mark that as radar
detected
* if NULL is passed, then mark all channel contexts as radar
detected
* Then as usual, schedule the radar detected work.
* In the worker, go over all the contexts again and for all such context
which is marked with radar detected, cancel the ongoing CAC by calling
ieee80211_dfs_cac_cancel() and then notify cfg80211 via
cfg80211_radar_event().
* To cancel the CAC, pass the channel context as well where radar is
detected to ieee80211_dfs_cac_cancel(). This ensures that CAC is
canceled only on the links using the provided context, leaving other
links unaffected.
This would also help in scenarios where there is split phy 5 GHz radio,
which is capable of DFS channels in both lower and upper band. In this
case, simultaneous radars can be detected.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20240906064426.2101315-9-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This allows the core code to change the channel. Code deduplication and
preparation for adding scanning code to the core.
Link: https://patch.msgid.link/20240828063422.44813-1-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Extend mt76_connac_mcu_sta_basic_tlv with the per-link STA configuration.
The patch we created is a prerequisite to enable the MLO function in the
driver. It is purely a refactoring patch so the functionality should
remain unchanged.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20240613030241.5771-38-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Extend mt7925_get_phy_mode with the per-link STA configuration.
The patch we created is a prerequisite to enable the MLO function in the
driver. It is purely a refactoring patch so the functionality should
remain unchanged.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20240613030241.5771-36-sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
mt76 patches for 6.10
- fixes
- mt7603 stability improvements
- mt7921 LED control
- mt7925 EHT radiotap support
|
|
In order to support color change with MLO, handle the link ID now
passed from cfg80211, adjust the code to do everything per link
and call the notifications to cfg80211 correctly.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240422053412.2024075-4-quic_adisi@quicinc.com
Link: https://msgid.link/20240422053412.2024075-5-quic_adisi@quicinc.com
Link: https://msgid.link/20240422053412.2024075-6-quic_adisi@quicinc.com
Link: https://msgid.link/20240422053412.2024075-7-quic_adisi@quicinc.com
[squash, move API call updates to this patch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Reduces size by avoiding duplicates
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Add pre-calibration for mt7986 and mt7916. It has different data size
with mt7915. Group cal needs 54k and 94k for 2G + 5G and 2G + 6G,
respectively. DPD cal needs 300k.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Send an update to the MCU whenever the settings change
Signed-off-by: MeiChia Chiu <MeiChia.Chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The mcu command format are different for mt7915 and mt7986.
Fix the mt7915_mcu_wed_wa_tx_stats to support mt7915 and mt7986.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Avoid potentially reusing uninitialized data
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Currently ieee80211_csa_finish() function finalizes CSA by scheduling a
finalizing worker using the deflink. With MLO, there is a need to do it
on a given link basis.
Pass link ID of the link on which CSA needs to be finalized.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240130140918.1172387-6-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For channel contexts, mac80211 currently uses the cfg80211
chandef struct (control channel, center freq(s), width) to
define towards drivers and internally how these behave. In
fact, there are _two_ such structs used, where the min_def
can reduce bandwidth according to the stations connected.
Unfortunately, with EHT this is longer be sufficient, at
least not for all hardware. EHT requires that non-AP STAs
that are connected to an AP with a lower bandwidth than it
(the AP) advertises (e.g. 160 MHz STA connected to 320 MHz
AP) still be able to receive downlink OFDMA and respond to
trigger frames for uplink OFDMA that specify the position
and bandwidth for the non-AP STA relative to the channel
the AP is using. Therefore, they need to be aware of this,
and at least for some hardware (e.g. Intel) this awareness
is in the hardware. As a result, use of the "same" channel
may need to be split over two channel contexts where they
differ by the AP being used.
As a first step, introduce a concept of a channel request
('chanreq') for each interface, to control the context it
requests. This step does nothing but reorganise the code,
so that later the AP's chandef can be added to the request
in order to handle the EHT case described above.
Link: https://msgid.link/20240129194108.2e88e48bd2e9.I4256183debe975c5ed71621611206fdbb69ba330@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
No need cast (void *) to (struct mt7615_phy *).
Signed-off-by: Wu Yunchuan <yunchuan@nfschina.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Without this patch, when ap sets the tx stream number to 2,
ap won't send any beamforming packet.
Fixes: f89f297aef28 ("mt76: mt7915: fix txbf starec TLV issues")
Signed-off-by: MeiChia Chiu <meichia.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Do not report cca and csa finish to upper layer on station type vif to
prevent warnings caused by setting beacon.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Use the correct ieee80211_conf of each band for IEEE80211_CONF_MONITOR
comparison.
Fixes: 24e69f6bc3ca ("mt76: fix monitor rx FCS error in DFS channel")
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
When the set_chan_info command is set with CH_SWITCH_NORMAL reason,
even if the action is UNI_CHANNEL_RX_PATH, it'll still generate some
unexpected tones, which might confuse DFS CAC tests that there are some
tone leakages. To get rid of these kinds of false alarms, always bypass
DPD calibration when IEEE80211_CONF_IDLE is set.
Reviewed-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Fix potential memory leak when setting beacon and inband discovery
commands.
Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Add CAP3_RX_CTRL_FRAME_TO_MULTIBSS check when setting sta_muru_tlv,
which is used to get stations's capability of receiving control frames
when running OFDMA with MBSSIDs.
Signed-off-by: Allen Ye <allen.ye@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
To accommodate 11v MBSSID IE and support maximum 16 MBSSIDs, expand the
beacon size limitation for beacon and inband discovery commands.
Co-developed-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Co-developed-by: Money Wang <money.wang@mediatek.com>
Signed-off-by: Money Wang <money.wang@mediatek.com>
Signed-off-by: MeiChia Chiu <meichia.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Correct per-device TLV lengths to avoid invalid operation in firmware.
( 64.040375:28:STATS-E)statsGetSingleHWCounter: MIB counter index = 65472 not supported.
This happens on mt7916/mt7986.
Fixes: b0bfa00595be ("wifi: mt76: mt7915: improve accuracy of time_busy calculation")
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Capabilities in vif->bss_conf are only initialized in AP mode.
For other modes, they should be enabled by default, in order to avoid a
mismatch.
Fixes: 885f7af7e544 ("wifi: mt76: mt7915: remove mt7915_mcu_beacon_check_caps()")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The stats are clear-on-read, which makes it very difficult for tools
to adequately deal with wrapped stats and with keeping good totals.
So, accumulate these values when they are read from the firmware/radio
and present totals to user-space.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Add support for the MediaTek MT7981 SoC which is similar to the MT7986
but with a newer IP cores and only 2x ARM Cortex-A53 instead of 4x.
Unlike MT7986 the MT7981 can only connect a single wireless frontend,
usually MT7976 is used for DBDC.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
PPDU TxS can only report MPDU count whereas mac80211 requires MSDU scale
(NL80211_STA_INFO_TX_PACKETS), so switch to get MSDU counts from WA
statistic.
Note that mt7915 WA firmware only counts tx_packet for WED path, so driver
needs to take care of host path additionally.
Fixes: 43eaa3689507 ("wifi: mt76: add PPDU based TxS support for WED device")
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The background radar uses MT_RX_SEL2 as its band indication, so fix it.
Fixes: 7a53eecd5c87 (wifi: mt76: mt7915: check the correctness of event data)
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Introduce p2p-go/p2p-client support to mt7921 driver
CONNECTION_P2P_GC/GO is not supported with the current firmware
so we added mt76_dev to mt76_connac_mcu_sta_basic_tlv signature to
use CONNECTION_INFRA_STA/AP instead for p2p-client and p2p-go
respectively to make it work.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
