| Age | Commit message (Collapse) | Author |
|---|
|
Hydra Home Agent is a device used to maintain cache coherency. Add support
for explicit cache maintenance operations using it. A system has multiple
of these agents. Whilst only one agent is responsible for a given cache
line, interleave means that for a range operation, responsibility for the
cache lines making up the range will typically be spread across multiple
instances.
Put this driver on a new Kconfig menu under drivers/cache. The short
description as memory hotplug like operations is intended to cover
the somewhat complex set of cases where this unit applies and differentiate
it clearly from typical non coherent DMA flows.
Co-developed-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Yushan Wang <wangyushan12@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
The next patch will add a new type of cache maintenance driver responsible
for flushing deeper than is necessary for non coherent DMA (current
use case of drivers/cache drivers), as needed when performing operations
such as memory hotplug and security unlocking of persistent memory. The two
types of operation are similar enough to share a drivers/cache directory
and MAINTAINERS but are otherwise currently unrelated.
To avoid confusion have two separate menus. Each has dependencies that are
implemented by making them boolean symbols, here CACHEMAINT_FOR_DMA
which is dependent on RISCV as all driver are currently for platforms of
that architecture. Set new symbol default to y to avoid breaking existing
configs. This has no affect on actual code built, just visibility of the
menu.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
This has a bunch of {read,write}q() calls, so it won't work on 32-bit
systems. I don't think there's any 32-bit StarFive systems, so for now
just require 64-bit.
Fixes: cabff60ca77d ("cache: Add StarFive StarLink cache management")
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Link: https://lore.kernel.org/r/20240722154519.25375-2-palmer@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Add StarFive Starlink cache management driver.
The driver enables RISC-V non-standard cache
operation on SoC that does not support Zicbom
extension instructions.
Signed-off-by: Joshua Yeong <joshua.yeong@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
Move the ccache driver over to drivers/cache, out of the drivers/soc
dumping ground, to this new collection point for cache controller
drivers.
Reviewed-by: Samuel Holland <samuel.holland@sifive.com>
Tested-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
|
|
RISCV_NONSTANDARD_CACHE_OPS is also used for the pmem cache maintenance
helpers, which are built into the kernel unconditionally.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231018052654.50074-2-hch@lst.de
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
I/O Coherence Port (IOCP) provides an AXI interface for connecting
external non-caching masters, such as DMA controllers. The accesses
from IOCP are coherent with D-Caches and L2 Cache.
IOCP is a specification option and is disabled on the Renesas RZ/Five
SoC due to this reason IP blocks using DMA will fail.
The Andes AX45MP core has a Programmable Physical Memory Attributes (PMA)
block that allows dynamic adjustment of memory attributes in the runtime.
It contains a configurable amount of PMA entries implemented as CSR
registers to control the attributes of memory locations in interest.
Below are the memory attributes supported:
* Device, Non-bufferable
* Device, bufferable
* Memory, Non-cacheable, Non-bufferable
* Memory, Non-cacheable, Bufferable
* Memory, Write-back, No-allocate
* Memory, Write-back, Read-allocate
* Memory, Write-back, Write-allocate
* Memory, Write-back, Read and Write-allocate
More info about PMA (section 10.3):
Link: http://www.andestech.com/wp-content/uploads/AX45MP-1C-Rev.-5.0.0-Datasheet.pdf
As a workaround for SoCs with IOCP disabled CMO needs to be handled by
software. Firstly OpenSBI configures the memory region as
"Memory, Non-cacheable, Bufferable" and passes this region as a global
shared dma pool as a DT node. With DMA_GLOBAL_POOL enabled all DMA
allocations happen from this region and synchronization callbacks are
implemented to synchronize when doing DMA transactions.
Example PMA region passes as a DT node from OpenSBI:
reserved-memory {
#address-cells = <2>;
#size-cells = <2>;
ranges;
pma_resv0@58000000 {
compatible = "shared-dma-pool";
reg = <0x0 0x58000000 0x0 0x08000000>;
no-map;
linux,dma-default;
};
};
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com> # tyre-kicking on a d1
Link: https://lore.kernel.org/r/20230818135723.80612-6-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
