| Age | Commit message (Collapse) | Author |
|---|
|
This device is powered by an FT232H, which is very similar to the
FT2232H this driver was written for. The key difference is it has only
one MPSSE instead of two. As a result, it presents only one USB
interface to the system, which conveniently "just works" out of the box
with this driver.
The brik exposes only two GPIO lines which are hardware limited to only
be useful in one direction. As a result, I've restricted things on the
driver side to refuse to configure any other lines.
This device, unlike the sealevel device I wrote this driver for
originally, is hotpluggable, which makes for all sorts of weird
edgecases. I've tried my best to stress-test the parts that could go
wrong, but given the new usecase, more heads taking a critical look at
the teardown and synchronization bits on the driver as a whole would be
appreciated.
Signed-off-by: Mary Strodl <mstrodl@csh.rit.edu>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20251014133530.3592716-5-mstrodl@csh.rit.edu
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Builds out a facility for specifying compatible lines directions and
labels for MPSSE-based devices.
* dir_in/out are bitmask of lines that can go in/out. 1 means
compatible, 0 means incompatible.
* names is an array of line names which will be exposed to userspace.
Also changes the chip label format to include some more useful
information about the device to help identify it from userspace.
Signed-off-by: Mary Strodl <mstrodl@csh.rit.edu>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20251014133530.3592716-4-mstrodl@csh.rit.edu
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
When an IRQ worker is running, unplugging the device would cause a
crash. The sealevel hardware this driver was written for was not
hotpluggable, so I never realized it.
This change uses a spinlock to protect a list of workers, which
it tears down on disconnect.
Signed-off-by: Mary Strodl <mstrodl@csh.rit.edu>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20251014133530.3592716-3-mstrodl@csh.rit.edu
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Not sure how I missed this, but errors encountered when setting the
direction to input weren't being propagated to the caller.
Signed-off-by: Mary Strodl <mstrodl@csh.rit.edu>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20251014133530.3592716-2-mstrodl@csh.rit.edu
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
The conversion of all GPIO drivers to using the .set_rv() and
.set_multiple_rv() callbacks from struct gpio_chip (which - unlike their
predecessors - return an integer and allow the controller drivers to
indicate failures to users) is now complete and the legacy ones have
been removed. Rename the new callbacks back to their original names in
one sweeping change.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
struct gpio_chip now has callbacks for setting line values that return
an integer, allowing to indicate failures. Convert the driver to using
them.
Link: https://lore.kernel.org/r/20250610-gpiochip-set-rv-gpio-v1-6-3a9a3c1472ff@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
ida_alloc() and ida_free() should be preferred to the deprecated
ida_simple_get() and ida_simple_remove().
This is less verbose.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/2ce706d3242b9d3e4b9c20c0a7d9a8afcf8897ec.1729423829.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Even if it's not critical, the avoidance of checking the error code
from devm_mutex_init() call today diminishes the point of using devm
variant of it. Tomorrow it may even leak something. Add the missed
check.
Fixes: c46a74ff05c0 ("gpio: add support for FTDI's MPSSE as GPIO")
Reviewed-by: Mary Strodl <mstrodl@csh.rit.edu>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20241030174132.2113286-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
FTDI FT2232H is a USB to GPIO chip. Sealevel produces some devices
with this chip. FT2232H presents itself as a composite device with two
interfaces (each is an "MPSSE"). Each MPSSE has two banks (high and low)
of 8 GPIO each. I believe some MPSSE's have only one bank, but I don't
know how to identify them (I don't have any for testing) and as a result
are unsupported for the time being.
Additionally, this driver provides software polling-based interrupts for
edge detection. For the Sealevel device I have to test with, this works
well because there is hardware debouncing. From talking to Sealevel's
people, this is their preferred way to do edge detection.
Signed-off-by: Mary Strodl <mstrodl@csh.rit.edu>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241009131131.1618329-1-mstrodl@csh.rit.edu
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
